Toro Polar Trac Cab 30474 Скачать руководство пользователя страница 34

Страница: 34 / 60

Use the coupler link, bolt (3/4 x 4 inches),
and washer to secure the winter frame to the
machine frame (

Figure 69

g032572

Figure 69

Coupler link

Bolt (3/4 x 4 inches)

Washer (3/4 inch)

Torque the bolt to 359 N∙m (265 ft-lb).

Securing the Cab to the Machine

Alternate between turning the lift screws, a few
turns at a time to lower the back of the cab to
the machine (

Figure 70

g032783

Figure 70

Lift screw

Use the bolt (1/2 x 3-1/4 inches) and (3/4 x 3-1/2
inches) to loosely install the cab-mount bracket
to each side of the ROPS tube (

Figure 71

g032662

Figure 71

Flange nut (1/2 inch)

Locknut (3/4 inch)

Cab-bracket mount

ROPS tube

Bolt (1/2 x 3-1/4 inches)

Bolt (3/4 x 3-1/2 inches)

Note:

Point the cab-bracket mount toward the

front of the machine.

Insert a rubber isolator at each of the mounting
locations on the cab frame (

Figure 72

g032784

Figure 72

Bolt (1/2 x 3-1/4 inches)

Cab frame

Large washer

Cab-mount bracket

Rubber isolator

Flange nut (1/2 inch)

Use the bolt (1/2 x 3-1/4 inches), large washer
and flange nut to mount cab to the machine
(

Figure 72

Tighten the bolt (1/2 x 3-1/4 inches) until the
rubber isolator is compressed to a thickness of
22 mm (0.875 inch).

Tighten the bolts and nuts securing the
cab-mount supports to the ROPS posts (

Figure

Содержание Polar Trac Cab 30474





























































Результаты поиска

Содержание Polar Trac Cab 30474

Отзывы:

Похожие инструкции для Polar Trac Cab 30474

Бренды по названию

Популярные бренды

Toro Polar Trac Cab 30474, Руководство оператора

Результаты поиска

Содержание Polar Trac Cab 30474

Отзывы:

Похожие инструкции для Polar Trac Cab 30474

Бренды по названию

Популярные бренды