manualshive.com logo in svg

Toro Polar Trac Cab 30474, Руководство оператора

Поделиться
Скачать
Toro Polar Trac Cab 30474 Скачать руководство пользователя страница 15

g032422

Figure 20

1.

Supply hose

3.

Straight fitting (3/8 NPT x
0.625 barb)

2.

Hose clamp (1/2 to 1-1/4
inches)

4.

Temperature sensor

3.

Apply sealant to the straight fitting (3/8 NPT x
0.625 barb); skipping the first thread.

4.

Finger-tighten the straight fitting into the port.

5.

Tighten the straight fitting 2 to 3 additional turns.

6.

Slide the hose clamp over the hose end (

Figure

20

).

7.

Insert the hose over straight fitting and secure
it with the hose clamp (1/2 to 1-1/4 inches) as
shown in

Figure 20

.

Routing the Return Hose

Kubota Engine Only

Route the return hose as shown in

Figure 21

.

g032423

Figure 21

1.

Supply hose

2.

Return hose

Moving the Temperature Sensor

Yanmar Engine Only

1.

Remove the socket terminal from the coolant
temperature sensor (

Figure 22

).

g233716

Figure 22

1.

Socket terminal
(coolant-temperature
sensor)

3.

Water-pump housing

2.

Temperature sensor

15

 

Содержание Polar Trac Cab 30474





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды