manualshive.com logo in svg

Toro Polar Trac Cab 30474, Руководство оператора

Поделиться
Скачать
Toro Polar Trac Cab 30474 Скачать руководство пользователя страница 16

2.

Remove the temperature sensor and gasket
from the rear port of the water pump (

Figure 23

).

Note:

Retain the temperature sensor for

installation in step

5

.

g233715

Figure 23

1.

Temperature sensor (old)

4.

Forward port (water-pump
housing)

2.

Gasket (temperature
sensor)

5.

Gasket (plug)

3.

Rear port (water-pump
housing)

6.

Plug

3.

Remove the plug and gasket from the forward
port of the water pump (

Figure 23

).

Note:

You no longer need the plug and gasket.

4.

Install the reducer and the gasket (plug) into the
forward port of the water pump (

Figure 24

).

g233712

Figure 24

1.

Reducer

3.

Forward port (water-pump
housing)

2.

O-ring

4.

Temperature sensor

5.

Apply PTFE thread sealant to the threads of the
temperature sensor that you removed in step

2

and to the threads of the straight barbed fitting.

6.

Install the new temperature sensor into the
reducer (

Figure 24

).

7.

Install the barbed fitting into the rear port of the
water-pump housing (

Figure 25

) and tighten the

fitting 2 to 3 turns beyond finger tight.

16

 

Содержание Polar Trac Cab 30474





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды