manualshive.com logo in svg

Toro Polar Trac Cab 30474, Руководство оператора


Поделиться
Скачать
background image

Note:

Do not secure the hoses to hot or moving

parts.

Installing the Washer Bottle

Yanmar Engine Only

1.

Use the 3 carriage bolts (5/16 x 2 inch), (5/16 x
1 inch), and 3 flange nuts to secure the bracket
to the frame (

Figure 33

).

g032448

Figure 33

1.

Bolt (5/16 x 2 inch)

3.

Bolts (5/16 x 1 inch)

2.

Flange nut (5/16 inch)

4.

Flange nut (5/16 inch)

2.

Torque the bolts to 1978 to 2542 N∙cm (175 to
225 in-lb).

3.

Use the 2 carriage bolts (5/16 x 3/4 inch) and
flange nuts to secure the washer bottle to the
bracket (

Figure 34

).

g032450

Figure 34

1.

Carriage bolt (5/16 x 3/4
inch)

2.

Flange nut (5/16 inch)

4.

Torque the bolts to 1978 to 2542 N∙cm (175 to
225 in-lb).

5.

Connect the washer tube to the washer bottle
and secure it to the frame with cable ties (

Figure

35

).

g032515

Figure 35

1.

Washer tube

Note:

Do not secure the hoses to hot or moving

parts.

20

 

Содержание Polar Trac Cab 30474





























































Отзывы:

Нет отзывов

Похожие инструкции для Polar Trac Cab 30474

Zell AC1000 Operation Manual preview
AC1000
Бренд: Zell Страницы: 33
Makita HR4013C Manual preview
HR4013C
Бренд: Makita Страницы: 20
Samsung EJ-FT810 Quick Start Manual preview
EJ-FT810
Бренд: Samsung Страницы: 7
Agri-Fab 45-03051 Owner'S Manual preview
45-03051
Бренд: Agri-Fab Страницы: 32
Samsung Flip WM55H Quick Setup Manual preview
Flip WM55H
Бренд: Samsung Страницы: 2
Abicor Binzel Abirob W600 Instruction Leaflet preview
Abirob W600
Бренд: Abicor Binzel Страницы: 8
babymoov a003205 Instruction Manual preview
a003205
Бренд: babymoov Страницы: 12
BabyOno 287 User Manual preview
287
Бренд: BabyOno Страницы: 24
babymoov Dream Belt Instructions For Use preview
Dream Belt
Бренд: babymoov Страницы: 4
Campbell SDM-CVO4 Features preview
SDM-CVO4
Бренд: Campbell Страницы: 2
i-onik WS-110 Quick Start Manual preview
WS-110
Бренд: i-onik Страницы: 6
LAUMAS TLM8 Installation And User Manual preview
TLM8
Бренд: LAUMAS Страницы: 44
Labona OLIVIA Technical Manual preview
OLIVIA
Бренд: Labona Страницы: 12
X10 MS12A Set Up And Operating Instructions preview
MS12A
Бренд: X10 Страницы: 1
Wavetronix smartsensor advance Installation & Quick Start Manual preview
smartsensor advance
Бренд: Wavetronix Страницы: 2
X-lite CLEO Installation Instructions preview
CLEO
Бренд: X-lite Страницы: 5
Xerox 6130N - Phaser Color Laser Printer Instruction Sheet preview
6130N - Phaser Color Laser Printer
Бренд: Xerox Страницы: 2
Varta element Series Add-On Instructions preview
element Series
Бренд: Varta Страницы: 132

Бренды по названию

Популярные бренды

Загрузить еще бренды