background image

9.

Remove the hour meter from the old control
panel and install it in the new control panel.

10.

Install the new control panel and plug the wire
into the hour meter.

11.

Secure the control panel in place with the
fasteners previously removed (

Figure 19

).

g003676

Figure 19

1.

Knob

2.

Control panel

12.

Install the knob onto the lift lever (

Figure 19

).

13.

Grease the front lift frame; refer to

Greasing the

Lift Frame (page 13)

.

14.

Check the hydraulic-fluid level and replenish the
fluid as required.

9

Reading/Storing the
Documentation

Parts needed for this procedure:

1

Operator’s Manual

Procedure

1.

Read the documentation.

2.

Store the documentation in a safe place.

Operation

Specifications

Net weight

38.5 kg (85 lb)

Attachments/Accessories

A selection of Toro approved attachments and
accessories is available for use with the machine to
enhance and expand its capabilities. Contact your
Authorized Service Dealer or Distributor or go to
www.Toro.com for a list of all approved attachments
and accessories.

Operating Tips

The front lift frame is designed to accept only
certain attachments. Do not try to install a rear
mount attachment to the front lift frame, as damage
to the machine may occur.

To lower the front lift frame, push the lift lever
forward.

To allow the front lift frame to float, push the lift
lever forward and to the side into the detent.

To raise the front lift frame, pull the lift lever
rearward.

Become familiar with the safe operation of the
equipment, with the operator controls, and safety
signs.

Keep hands and feet away from moving parts and
hot surfaces.

Maintenance

Greasing the Lift Frame

The front lift frame has 5 grease fittings (

Figure 20

)

that must be lubricated regularly with No. 2 lithium
grease. If the machine is operated under normal
conditions, lubricate all bearings and bushings after
every 100 hours of operation. Lubricate the bearings
and bushings immediately

after every

washing,

regardless of the interval listed.

13

 

Содержание Infield Pro 08712





















Отзывы: