Toro Groundsmaster 5900 Series Скачать руководство пользователя страница 14

Declaration of Incorporation

The Toro Company, 8111 Lyndale Avenue South, Bloomington, MN, USA declares that the following unit(s)
conform(s) to the directives listed, when installed in accordance with the accompanying instructions onto certain
Toro models as indicated on the relevant Declarations of Conformity.

Model No.

Serial No.

Product Description

Invoice Description

General Description

Directive

30653

400000000 and Up

EU Light Kit, Serial Number

400000000 and After

Groundsmaster 5900

or 5910 Series Rotary

Mower with Cab

EU LIGHT KIT -

GM5900/5910 T4F MODELS

EU Light Kit

2014/30/EU

Relevant technical documentation has been compiled as required per Part B of Annex VII of 2014/30/EU.

We will undertake to transmit, in response to requests by national authorities, relevant information on this partly
completed machinery. The method of transmission shall be electronic transmittal.

This machinery shall not be put into service until incorporated into approved Toro models as indicated on the
associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in
conformity with all relevant Directives.

Certified:

EU Technical Contact:

Marcel Dutrieux
Manager European Product Integrity
Toro Europe NV
Nijverheidsstraat 5
2260 Oevel

John Heckel

Belgium

Sr. Engineering Manager
8111 Lyndale Ave. South

Tel. +32 16 386 659

Bloomington, MN 55420, USA
February 6, 2017

 

Содержание Groundsmaster 5900 Series

















Отзывы: