Toro Greensmaster TriFlex 3400 Series страница 39 Скачать руководство пользователя | Manualshive

Страница: 39 / 48

background image

WARNING

Battery terminals or metal tools could short
against metal tractor components causing
sparks. Sparks can cause the battery gasses
to explode, resulting in personal injury.

•

When removing or installing the battery,
do not allow the battery terminals to touch
any metal parts of the tractor.

•

Do not allow metal tools to short between
the battery terminals and metal parts of the
tractor.

WARNING

Incorrect battery cable routing could damage
the tractor and cables causing sparks. Sparks
can cause the battery gasses to explode,
resulting in personal injury.

If corrosion occurs at the terminals,
disconnect the cables, negative (-) cable
first, and scrape the clamps and terminals
separately. Reconnect the cables, positive
(+) cable first, and coat the terminals with
petroleum jelly.

•

Always disconnect the negative (black)
battery cable before disconnecting the
positive (red) cable.

•

Always connect the positive (red) battery
cable before connecting the negative
(black) cable.

Storing the Battery

If the machine will be stored more than 30 days,
remove the battery and charge it fully. Either store
it on the shelf on the machine. Leave the cables
disconnected if it is stored on the machine. Store
the battery in a cool atmosphere to avoid quick
deterioration of the charge in the battery. To prevent
the battery from freezing, make sure it is fully charged.
The specific gravity of a fully charged battery is
1.265–1.299.

Locating the Fuses

The fuses in the machine’s electrical system are
located under the seat (

).

g014617

Figure 46

1.

Fuses

2.

50 A fuse for radiator fan
(behind parts illustrated)

Fuse Layout

Lift Reel

E-Reel Enable

Over Temp

7.5 A

Reel Engage

Lights

Lift/Lower

Leak Detector

Fan

15 A

7.5 A

Start/Run

Starter

Diag. Lights

Glow

15 A

7.5 A

Run

ECM Logic

Power

10 A

2 A

39

«
...
37
38
39
40
41
...
»

Содержание Greensmaster TriFlex 3400 Series

















































Отзывы:

Нет отзывов

Похожие инструкции для Greensmaster TriFlex 3400 Series

Бренд: Gallagher Страницы: 6

Бренд: Quincy lab Страницы: 4

Бренд: MADRIX Страницы: 12

Бренд: Rane Страницы: 88

Бренд: Sentinel Страницы: 4

Бренд: PASCO Страницы: 36

Бренд: Labnet Страницы: 21

Бренд: AlcoSense Страницы: 10

Бренд: Biosan Страницы: 16

EPL-SL-5X75-12V-TXF

Бренд: Larson Electronics Страницы: 2

CLASSIC H.R. UV-C SPA

Бренд: Elecro Engineering Страницы: 16

Бренд: Zadro Страницы: 12

Net 'N' Clean 22514

Бренд: Astralpool Страницы: 30

Бренд: involight Страницы: 53

Бренд: WaferLight Страницы: 18

home LS 5000SOUND

Бренд: Somogyi Elektronic Страницы: 10

Zombies 12xx Series

Бренд: Quantec Страницы: 145

Бренд: MAHLE Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды