Toro Greensmaster TriFlex 3400 Series Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 48

Toro Greensmaster TriFlex 3400 Series Скачать руководство пользователя страница 15

WARNING

Battery terminals or metal tools could
short against metal tractor components
causing sparks. Sparks can cause the
battery gasses to explode, resulting in
personal injury.

•

When removing or installing the
battery, do not allow the battery
terminals to touch any metal parts of
the tractor.

•

Do not allow metal tools to short
between the battery terminals and
metal parts of the tractor.

WARNING

Failure to correctly activate the battery
may result in battery gassing and/or
premature battery failure.

7.

Place the battery on the battery tray and secure
it with the battery clamp and fasterners removed
previously.

8.

Install the positive cable (red) to the positive (+)
terminal and then the negative cable (black)
to the negative (–) terminal of the battery and
secure them with the bolts and nuts (

).

Slide the rubber boot over the positive terminal
to prevent a possible short from occurring.

WARNING

Incorrect battery cable routing could damage
the tractor and cables causing sparks. Sparks
can cause the battery gasses to explode,
resulting in personal injury.

•

Always disconnect the negative (black)
battery cable before disconnecting the
positive (red) cable.

•

Always connect the positive (red) battery
cable before connecting the negative
(black) cable.

g005098

Figure 7

1.

Negative (-)

2.

Positive (+)

5

Installing the Oil Cooler
(optional)

No Parts Required

Procedure

If you are operating the machine in hot climates,
where ambient temperatures are above 29° C (85°
F), or using it for heavy-duty use (mowing other than
greens, such as fairways or verticutting), install a
Hydraulic Oil Cooler Kit, Part No. 117-9314, to the
machine.

15

«
...
13
14
15
16
17
...
»

Содержание Greensmaster TriFlex 3400 Series

















































Отзывы:

Нет отзывов