manualshive.com logo in svg

Toro Greensmaster TriFlex 3400 Series, Руководство оператора, Страница: 46 / 48

Поделиться
Скачать
Toro Greensmaster TriFlex 3400 Series Скачать руководство пользователя страница 46

Storage

If you wish to store the machine for a long period of
time, the following steps should be performed prior
to storage:

1.

Remove accumulations of dirt and old grass
clippings. Sharpen the reels and bedknives, if
necessary; refer to the

Cutting Unit Operator's

Manual

. Use a rust preventive on bedknives and

reel blades. Grease and oil all lubrication points.

2.

Block up the wheels to remove any weight on
the tires.

3.

Drain and replace the hydraulic fluid and filter
and inspect the hydraulic lines and fittings.
Replace, if necessary; refer to

Changing the

Hydraulic Oil and Filter (page 43)

and

Checking

the Hydraulic Lines and Hoses (page 43)

.

4.

All fuel should be removed from the fuel tank.
Run the engine until it stops from lack of fuel.
Replace the fuel filter; refer to

Servicing the Fuel

Filter/Water Separator (page 37)

.

5.

While the engine is still warm, drain the oil from
the crankcase. Refill it with fresh oil; refer to

Changing the Engine Oil and Filter (page 36)

.

6.

Clean dirt and chaff from the cylinder, cylinder
head fins, and blower housing.

7.

Remove the battery and charge it fully. Either
store it on the shelf or on the machine. Leave
the cables disconnected if it is stored on the
machine. Store the battery in a cool atmosphere
to avoid quick deterioration of the charge in the
battery.

8.

If possible, store the machine in a warm, dry
location.

46

 

Содержание Greensmaster TriFlex 3400 Series

















































Отзывы:

Нет отзывов