manualshive.com logo in svg

Toro Greensmaster TriFlex 3400 Series, Руководство оператора, Страница: 13 / 48

Поделиться
Скачать
Toro Greensmaster TriFlex 3400 Series Скачать руководство пользователя страница 13

1

Installing the Roll Bar

Parts needed for this procedure:

1

Roll bar

4

Bolt (1/2 x 3-3/4 inches)

4

Flange-nut (1/2 inch)

Procedure

1.

Remove the top crate support from the crate.

2.

Remove the roll bar from the crate.

3.

Install the roll bar into the pockets on each side
of the machine, using 4 bolts (1/2 x 3-3/4 inches)
and 4 flange-nuts (1/2 inch) (

Figure 3

).

g014601

Figure 3

1.

Roll bar

3.

Flange-nut (1/2 inch)

2.

Bolt (1/2 x 3-3/4 inches)

4.

Torque the fasteners to 136 to 149 N-m (100 to
110 ft-lb).

2

Installing the Seat

Parts needed for this procedure:

1

Seat completion kit

Procedure

Acquire your desired seat kit from your distributor and
install it as directed in the instruction included with
the kit.

3

Installing the Steering
Wheel

Parts needed for this procedure:

1

Steering wheel

1

Locknut (1-1/2 inches)

1

Washer

1

Steering wheel cap

Procedure

1.

Slide the steering wheel onto the steering shaft
(

Figure 4

).

g010834

Figure 4

1.

Steering wheel

3.

Jam nut

2.

Washer

4.

Cap

2.

Slide the washer onto the steering shaft (

Figure

4

).

13

 

Содержание Greensmaster TriFlex 3400 Series

















































Отзывы:

Нет отзывов