Toro Greensmaster TriFlex 3400 Series страница 18 Скачать руководство пользователя | Manualshive

Страница: 18 / 48

background image

8

Adding Rear Weight

Parts needed for this procedure:

1

Weight kit, 121–6665 (purchase separately)

Note:

This kit is not required for units with the 3 wheel drive
kit installed.

Procedure

This unit complies with the ANSI B71.4-2004 and
EN 836 Standards when equipped with weight kit
121–6665.

Note:

If the unit is equipped with a three wheel drive

kit additional weight is not required to meet ANSI
B71.4-2004 and EN 836 standards.

9

Installing the CE Guard Kit

Parts needed for this procedure:

1

CE Guard Kit―Part No. 04442 (sold separately)

Procedure

Install the CE guard kit; refer to the CE Guard Kit for
Greensmaster 3400 TriFlex Traction Unit Installation
instructions.

10

Installing EU Decals

Parts needed for this procedure:

1

Warning decal 117-9537

Procedure

If this machine will be used in the EU, affix the warning
decal 117-9537 over English warning decal 117-9536.

Product Overview

g014674

Figure 14

1.

Engine

5.

Steering wheel

2.

Roll bar

6.

Traction pedal

3.

Control panel

7.

Foot rest

4.

Seat

8.

Reels with grass baskets

Controls

Traction Pedal

The traction pedal (

) has three functions:

to make the machine move forward, to move it
backward, and to stop the machine. Press the top
of the pedal to move forward and the bottom of the
pedal to move backward or to assist in stopping when
moving forward. Also, allow the pedal to move to the
neutral position to stop the machine. For operator
comfort, do not rest the heel of your foot on reverse
when operating forward (

18

«
...
16
17
18
19
20
...
»

Содержание Greensmaster TriFlex 3400 Series

















































Отзывы:

Нет отзывов

Похожие инструкции для Greensmaster TriFlex 3400 Series

Бренд: NAD Страницы: 10

Бренд: Safavieh Страницы: 2

APT-9411 Series

Бренд: TAKAYA Страницы: 77

Бренд: REED Страницы: 12

ikon profile ww

Бренд: ADJ Страницы: 15

Multi Use Tester III

Бренд: Fuso Страницы: 92

Бренд: Sure-Lites Страницы: 6

Бренд: Murphy Страницы: 20

Бренд: REITEL Страницы: 20

Бренд: Velleman Страницы: 4

Бренд: National Instruments Страницы: 26

Бренд: Iluminar Страницы: 8

Бренд: Vari Lite Страницы: 2

Бренд: Gardol Страницы: 236

Бренд: Laserworld Страницы: 6

Бренд: Tanaka Страницы: 28

Бренд: ZK Страницы: 66

Бренд: hidealite Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды