manualshive.com logo in svg

Toro 68013, Руководство оператора

Поделиться
Скачать
Toro 68013 Скачать руководство пользователя страница 41

1

2

G020010

Figure 72

1.

Bolt

2.

Belt guide

4.

Slip the forward belt forward and off the idler pulley
(Figure 73).

2

3

4

1

G020012

Figure 73

1.

Engine pulley

3.

Idler pulley

2.

Forward belt

4.

Rear belt

5.

Slip the rear belt rearward and off the idler pulley
(Figure 73).

6.

Slip the belts off the engine pulley.

7.

Remove the belts from the machine.

Installing the Belts

1.

Ensure that the clutch lever is in the Off position; refer
to Controlling the Paddles (page 22).

2.

Align the rear belt to the rear groove in the engine
pulley.

Note:

Do not align the rear belt to the idler pulley.

3.

Align the forward belt to the forward groove of the
idler pulley.

4.

Slip the rear belt over the idler pulley and align the belt
to the rear pulley groove.

5.

Slip the forward belt over the engine pulley and align
the belt to the forward pulley groove.

6.

Check the belt tension; refer to step 1, step 2, and step
3 in Adjusting the Belt Tension (page 39).

7.

Loosely secure the belt guide to the engine (Figure 72)
with the bolt that was removed in step 3 of Removing
the Belts (page 40).

8.

Adjust the belt guide; refer to Adjusting the Belt Guide
(page 41).

9.

Install the divider plate; refer to Installing the Divider
Plate (page 28).

Adjusting the Belt Guide

Note:

To access the belt guide, remove the divider plate;

refer to Removing the Divider Plate (page 28).

Guide air gap:

2.5 to 4.0 mm (3/32 to 5/32 inch)

1.

Ensure that the clutch lever is in the On position; refer
to Controlling the Paddles (page 22).

2.

Ensure that the belt tension is correct; refer to
Adjusting the Belt Tension (page 39).

3.

Check that the air gap between the belt guide and the
belts is 2.5 to 4.0 mm (3/32 to 5/32 inch); refer to
Figure 74.

G02001 1

3

4

5

1

2

Figure 74

1.

Engine pulleys

4.

Belt guide

2.

Belts

5.

Bolt

3.

Guide air gap: 2.5 to 4.0
mm (3/32 to 5/32 inch)

4.

If the air gap is not within the specified range, do the
following:

A.

Loosen the bolt that secures the belt guide to the
engine (Figure 74).

Important:

Ensure that the belt guide is

toward the engine pulley.

B.

Rotate the belt guide up or down until there is
an air gap of 2.5 to 4.0 mm (3/32 to 5/32 inch)
between the guide and each belt (Figure 74).

41

Содержание 68013

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды