manualshive.com logo in svg

Toro 68013, Руководство оператора

Поделиться
Скачать
Toro 68013 Скачать руководство пользователя страница 22

G019747

Figure 35

Note:

If the choke lever is set to the Closed position to start

the engine, gradually move the choke lever back toward the
Open position as the engine warms up. If the engine stalls
or hesitates, move the choke lever back toward the Closed
position until the engine runs smooth. Allow the engine to
warm up, then move the choke lever to the Open position;
refer to Choke Lever (page 12).

Stopping the Engine

WARNING

In an emergency situation, stop the engine
immediately.

Important:

During normal operation, if the engine

has been working hard or is hot, let it idle for a minute
before stopping the engine. This helps to cool the
engine before stopping.

1.

Ensure that the choke lever is in the Off position
(Figure 34); refer to Choke Lever (page 12).

2.

Move the throttle lever to the Min position (Figure 34);
refer to Throttle Lever (page 12).

3.

Rotate the engine switch to the Off position; refer to
Engine On/Off Switch (page 12).

Controlling the Paddles

DANGER

This machine is capable of amputating hands.

•

Stay in the operator’s position while the machine
is running.

•

Keep all bystanders a safe distance from the
machine.

•

Stop the machine immediately if any people or
animals enter the work area.

•

Never place any part of your body into a position
that causes an unsafe operating condition.

Important:

Ensure that the paddles do not turn when

clutch is in the Off position.

Use the clutch lever to control the power transmission to the
paddles of the machine.

Controlling the Paddles—Belt-drive
Models

Models 68013, 68014, 68016, 68017, 68020, and 68021 only

G019873

1

2

Figure 36

1.

Off position

2.

On position

22

Содержание 68013

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды