manualshive.com logo in svg

Toro 68013, Руководство оператора

Поделиться
Скачать
Toro 68013 Скачать руководство пользователя страница 20

Add the correct amount of fuel stabilizer/conditioner to the
fuel, and follow the directions of the manufacturer.

Note:

Fuel stabilizer/conditioner is most effective when

mixed with fresh fuel. To minimize the chance of varnish
deposits in the fuel system, use fuel stabilizer at all times.

Filling the Fuel Tank

Model(s)

Fuel tank capacity

68013 and 68014

3.1 L (0.82 US gallons)

68016, 68017, 68020, 68021

5.3 L (1.40 US gallons)

68024

6.1 L (1.61 US gallons)

1.

Park the machine on a level surface, stop the engine,
and allow the engine to cool.

2.

Clean around the fuel cap and remove it (Figure 30).

1

G019799

Figure 30

1.

Fuel cap

3.

Add unleaded gasoline to the fuel tank, until the level
is at the bottom of the maximum fuel level, as shown
in Figure 31.

Important:

This space in the tank allows gasoline

to expand. Do not fill the fuel tank completely full.

G020679

1

Figure 31

1.

Maximum fuel level

4.

Install the fuel cap securely (Figure 30).

5.

Wipe up any gasoline that may have spilled.

Checking the Engine Oil Level

Service Interval:

Before each use or daily

Important:

Use 4-cycle engine oil that meets or exceeds

the requirements for API service category

SJ, SL, SM,

or higher

.

Model(s)

Crankcase capacity

68013 and 68014

0.58 L (0.61 US qt)

68016, 68017, 68020, 68021,
68024

1.1 L (1.2 US qt)

Important:

If the oil level in the crankcase is too low

or too high and you run the engine, you may damage
the engine. This type of damage is not covered by the
warranty.

Note:

Use SAE 10W-30 for general use. You can use

the other viscosities shown in the chart when the average
temperature in your area is within the indicated range (Figure
32).

20

Содержание 68013

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды