Toro 41188 Скачать руководство пользователя

Страница: 329 / 353

Multi Pro 1750

Page 9 − 19

Ultra Sonic Boom Kit (Optional)

ÁÁÁÁÁÁÁÁÁÁÁÁÁ

Problem

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Possible Cause

ÁÁÁÁÁÁÁÁÁÁÁÁÁ

One of the booms does not automat-
ically follow ground irregularities.
Boom can be controlled with boom
lift switch.

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

On affected boom, the sonic boom sensor cover is on sensor.

On affected boom, calibration of the sonic boom sensors is incor-
rect.

The sonic boom sensor is incorrectly installed.

Sonic boom sensor or circuit wiring for affected boom is faulty.

The Toro Electronic Controller (TEC) or circuit wiring is faulty.

ÁÁÁÁÁÁÁÁÁÁÁÁÁ

Neither boom automatically follows
ground irregularities. Booms can be
controlled with boom lift switches.

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Sonic boom switch is not in the AUTOMATIC position.

Sonic boom sensor covers are on both sensors.

Calibration of the sonic boom sensors is incorrect.

Both sonic boom sensors or circuit wiring are faulty.

The Toro Electronic Controller (TEC) or circuit wiring is faulty.

Ultra Sonic

Boom (Opt.)

Содержание 41188


































































































































































































































































































































































Результаты поиска

Содержание 41188

Отзывы:

Похожие инструкции для 41188

Бренды по названию

Популярные бренды

Toro 41188, Руководство по обслуживанию

Результаты поиска

Содержание 41188

Отзывы:

Похожие инструкции для 41188

Бренды по названию

Популярные бренды