Toro 39094 Скачать руководство пользователя страница 47

Страница: 47 / 52

Problem

Possible Cause

Corrective Action

1. Drive belt is worn, loose or broken.

1. Check the belt tension.

2. Drive belt is off pulley.

2. Install drive belt and check adjusting

shafts and belt guides for correct
position.

3. Deck belt is worn, loose or broken.

3. Install new deck belt.

4. Deck belt is off pulley.

4. Install deck pulley and check the idler

pulley, idler arm and spring for correct
position and function.

5. Broken or missing idler spring.

5. Replace the spring.

6. Electric clutch out of adjustment.

6. Adjust the clutch air gap.

7. Clutch connector or wire damaged.

7. Contact an Authorized Service Dealer.

8. Damaged electric clutch.

8. Contact an Authorized Service Dealer.

9. Safety interlock system prevents blade

rotation.

9. Contact an Authorized Service Dealer.

Blades do not rotate.

10. PTO switch is faulty.

10. Contact an Authorized Service Dealer.

Содержание 39094





















































Результаты поиска

Содержание 39094

Отзывы:

Похожие инструкции для 39094

Бренды по названию

Популярные бренды

Toro 39094, Руководство оператора

Результаты поиска

Содержание 39094

Отзывы:

Похожие инструкции для 39094

Бренды по названию

Популярные бренды