Toro 39094 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 52

background image

Blade Control Bail

The bail is used in conjunction with the power take off
switch (PTO) to engage the clutch to drive the mower
blades. Release the mower control bail to disengage the
mower blades.

Power Take Off Switch (PTO)

This pull switch is used in conjunction with the blade
control bail to engage the clutch to drive the mower
blades.

Gear Shift Lever

The transmission has five forward speeds, neutral and
reverse, and has an in-line shift pattern.

Important:

Do not shift while unit is moving, as

transmission damage may occur.

Upper Control Bar

Shift to the desired gear and push forward on the upper
control bar to engage forward traction operation and
pull back to brake forward movement. Pull back on
right side of upper control bar to turn right and left side
to turn left.

Lower Control Bar

Shift transmission to reverse and squeeze the lower
control bar and handle together to engage rearward
traction assist operation.

Parking Brake Lever

Pull back on upper control bar and swing brake lever up
against the upper handle (Figure 4).

Ignition Switch

This switch is used in conjunction with recoil starter and
has two positions:

Run

and

Off

.

Recoil Starter

Pull recoil starter handle to start engine (not shown in
Figure 4).

Fuel Shut-off Valve

Close the fuel shut-off valve when transporting or
storing mower.

Specifications

Note:

Specifications and design are subject to change

without notice.

36 inch mowers:

Width with deflector down

51–1/8 inches (130 cm)

Length

82–3/4 inches (210 cm)

Height with handle in lowest
position

41–3/16 inches (105 cm)

Weight

588 lb (267 kg)

40 inch mowers:

Width with deflector down

55–1/2 inches (141 cm)

Length

79–1/2 inches (202 cm)

Height with handle in lowest
position

41–3/16 inches (105 cm)

Weight

596 lb (270 kg)

Attachments/Accessories

A selection of Toro approved attachments and
accessories are available for use with the machine to
enhance and expand its capabilities. Contact your
Authorized Service Dealer or Distributor or go to
www.Toro.com for a list of all approved attachments
and accessories.

11

«
...
9
10
11
12
13
...
»

Содержание 39094





















































Отзывы:

Нет отзывов

Похожие инструкции для 39094

Бренд: McCulloch Страницы: 36

Бренд: LAZER Страницы: 20

Бренд: Qualcast Страницы: 20

Бренд: Troy-Bilt Страницы: 88

Бренд: Jacobsen Страницы: 20

NZMX30614KH, NZMX32734BV

Бренд: Snapper Страницы: 13

Бренд: Worx Страницы: 132

Бренд: Simplicity Страницы: 80

Бренд: ARNETOLI MOTOR Страницы: 2

Бренд: Kubota Страницы: 24

Бренд: Husqvarna Страницы: 37

Бренд: Husqvarna Страницы: 36

Бренд: Husqvarna Страницы: 40

Бренд: Husqvarna Страницы: 32

Бренд: Husqvarna Страницы: 20

Бренд: Husqvarna Страницы: 20

Бренд: Husqvarna Страницы: 20

Бренд: Husqvarna Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды