manualshive.com logo in svg

Toro 30643, Руководство оператора

Поделиться
Скачать
Toro 30643 Скачать руководство пользователя страница 57

Belt Maintenance

Servicing the Alternator Belt

Service Interval:

After the first 10 hours

Every 100 hours

Proper tension allows 10 mm (3/8 inch) of deflection when
a force of 44 N∙m (10 ft-lb) is applied on the belt midway
between the pulleys.

If the deflection is not 10 mm (3/8 inch), loosen the
alternator-mounting bolts (

Figure 72

).

Note:

Increase or decrease the alternator-belt tension and

tighten the bolts. Check the deflection of the belt again to
ensure that the tension is correct.

Figure 72

1.

Alternator

3.

Compressor

2.

Mounting bolt

4.

Idler pulley

Servicing the Air Conditioner
Compressor Belt

Service Interval:

After the first 10 hours

Every 100 hours

Cab model only

Check the condition and tension of the belt (

Figure 72

) after

every 100 operating hours.

1.

Proper tension will allow 10 mm (3/8 inch) deflection
when a force of 44 N (10 lb) is applied on the belt
midway between the pulleys.

2.

If the deflection is not 10 mm (3/8 inch), loosen the
idler pulley mounting bolt (

Figure 72

). Increase or

decrease the compressor belt tension and tighten the
bolt. Check the deflection of the belt again to ensure
that the tension is correct.

Tensioning the Blade-Drive
Belts

Service Interval:

After the first 10 hours

Every 50 hours

When properly tensioned, the inside measurement of the
extension spring (hook to hook) should be approximately
8.3 to 9.5 cm (3-1/4 to 3-3/4 inches). Once the correct
spring tension is attained, adjust the stop bolt (carriage bolt)
until there is approximately 2 to 5 mm (0.065 to 0.185 inch)
clearance between the head of the bolt and the idler arm
(

Figure 73

).

Note:

Ensure that the belt is positioned on the spring side

of the belt guide (

Figure 73

).

Figure 73

1.

Belt

4.

Belt guide

2.

Eye bolt

5.

Flange nut

3.

Extension spring

6.

Stop bolt

Replacing the Blade-Drive Belt

Service Interval:

Every 800 hours

The blade-drive belt, tensioned by the spring-loaded idler
pulley, is very durable. However, after many hours of use,
the belt will show signs of wear. Signs of a worn belt are:
squealing when the belt is rotating, blades slipping when
cutting grass, frayed edges, burn marks, and cracks. Replace
the belt if any of these conditions are evident.

1.

Lower the mower deck to the shop floor, remove the
belt covers from the top of the mower deck, and set
the covers aside.

2.

Loosen the eye bolt allowing the removal of the
extension spring (

Figure 73

).

3.

Loosen the flange nut securing the stop bolt to the
mounting tab and move the idler pulley away from the
belt to release the belt tension (

Figure 73

).

Note:

Loosen the nut enough to allow the idler arm

to pass the stop bolt.

57

 

Содержание 30643









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды