manualshive.com logo in svg

Toro 30643, Руководство оператора

Поделиться
Скачать
Toro 30643 Скачать руководство пользователя страница 11

114–0846

1.

Read the

Operator’s

Manual

for information on

starting the engine—1) Set
to neutral; 2) Engage the
brake; 3) Set the engine
speed to slow; 4) Turn the
ignition key to preheat; 5)
Turn the ignition key to
engine start.

4.

Pull the knob out to
engage the PTO.

2.

Read the

Operator’s

Manual

for information on

shutting off the engine—1)
Set the engine speed to
slow; 2) Disengage the
deck; 3) Lock the parking
brake; 4) Wait 5 minutes;
5) Turn the ignition key to
engine stop; 6) Remove
the key from the ignition.

5.

Push the knob in to
disengage the PTO.

3.

Read the

Operator’s

Manual

.

6.

Raise the decks to go to H
range.

Battery Symbols

Some or all of these symbols are on your battery

1.

Explosion hazard

6.

Keep bystanders a safe
distance from the battery.

2.

No fire, open flame, or
smoking

7.

Wear eye protection;
explosive gases can
cause blindness and other
injuries

3.

Caustic liquid/chemical
burn hazard

8.

Battery acid can cause
blindness or severe burns.

4.

Wear eye protection.

9.

Flush eyes immediately
with water and get medical
help fast.

5.

Read the

Operator's

Manual.

10.

Contains lead; do not
discard

120-6604

1.

Thrown object hazard—keep bystanders away from the
machine.

2.

Cutting/dismemberment hazard of hand, mower
blade—stay away from moving parts; keep all guards and
shields in place.

3.

Cutting/dismemberment hazard of foot, mower blade—stay
away from moving parts; keep all guards and shields in
place.

11

 

Содержание 30643









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды