manualshive.com logo in svg

Toro 30643, Руководство оператора

Поделиться
Скачать
Toro 30643 Скачать руководство пользователя страница 41

Maintenance Service

Interval

Maintenance Procedure

Every 800 hours

• Drain and clean the fuel tank (also if the fuel system is contaminated).
• Change the front planetary-gear oil.
• Change the rear-axle lubricant.
• Check the rear wheel toe-in.
• Inspect the blade-drive belt.
• Change the hydraulic fluid. Change the hydraulic fluid after every 800 operating

hours, in normal conditions. If the fluid becomes contaminated, contact your local
Toro distributor because the system must be flushed. Contaminated fluid looks milky
or black when compared to clean fluid.

• Change the hydraulic filters.
• Inspect the mower deck caster-wheel assemblies.

Every 1,000 hours

• Check and adjust the engine-valve clearance.

Every 2 years

• Flush the cooling system and replace the fluid.
• Replace moving hoses.

CAUTION

If you leave the key in the ignition switch, someone could accidently start the engine and seriously injure
you or other bystanders.

Remove the key from the ignition before you do any maintenance.

Daily Maintenance Checklist

Duplicate this page for routine use.

For the week of:

Maintenance Check Item

Monday

Tuesday

Wednesday

Thursday

Friday

Saturday

Sunday

Check the safety-interlock
operation.

Check the brake operation.

Check the engine-oil level.

Check the
cooling-system-fluid level.

Drain the water/fuel
separator.

Check the air filter, dust cup,
and burp valve.

Check for unusual engine
noises.

2

Check the radiator and
screen for debris

Check for unusual operating
noises.

Check the hydraulic-system-
oil level.

Check the hydraulic hoses
for damage.

Check for fluid leaks.

Check the fuel level.

Check the tire pressure.

41

 

Содержание 30643









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды