Toro 04650 Скачать руководство пользователя страница 5

3

Installing the Adapter Kit

Units Without a Groomer Only

Parts needed for this procedure:

1

Adapter kit—Part No. 132-0723 (sold separately)

Procedure

For a cutting unit without a groomer, the adapter kit
provides the necessary mounting points for installing
the brush kit.

1.

Remove the screws securing the weight and
remove the weight (

Figure 7

).

g032588

Figure 7

1.

Weight

3.

Cap

2.

Screw

2.

Remove the cap from the center of the weight
(

Figure 7

).

3.

Restrain the reel; refer to

Restraining the Reel

for Removing Threaded Inserts (page 12)

.

4.

Remove the bearing screw (

Figure 8

).

Note:

If the bearing screw is on the right side

of the cutting unit, it has standard right-hand
threads. If it is on the left side of the cutting unit,
it has left-hand threads.

g032589

Figure 8

1.

Bearing screw

5.

Secure the driveshaft to the driveshaft adapter
(

Figure 9

) and torque it to 149 to 162 N∙m (110

to 120 ft-lb).

Note:

The kit includes 2 driveshaft adapters—1

for a right drive configuration (

silver

, right-hand

threads) and 1 for a left drive configuration
(

black

, left-hand threads).

g032597

Figure 9

Left Drive Configuration Shown

1.

Driveshaft

3.

Shim washer

2.

Driveshaft adapter (

black

,

left-hand threads)

6.

Restrain the reel; refer to

Restraining the Reel

for Installing Threaded Inserts (page 13)

.

7.

Torque the drive shaft adapter assembly to the
reel and torque to 135 to 150 N∙m (100 to 110
ft-lb).

Note:

For a cutting unit requiring the left drive

configuration, install the shim washer under the
driveshaft adapter (

Figure 9

).

8.

Install the weight with the screws that you
removed in step

1

(

Figure 10

).

5

 

Содержание 04650

















Отзывы: