Toro 04650 Скачать руководство пользователя страница 12

Maintenance

Restraining the Reel

WARNING

The cutting reel blades are sharp and capable
of amputating hands and feet.

Keep your hands and feet outside of the
reel.

Ensure that the reel is restrained before
servicing it.

Restraining the Reel for Removing
Threaded Inserts

1.

Tip up the cutting unit so that you access the
bottom of the reel.

2.

Insert a long-handled pry bar (recommended 3/8
x 12 inches with screwdriver handle) through the
bottom of the cutting reel, closest to the side of
the cutting unit that you are torquing (

Figure 25

).

3.

Place the pry bar against the weld side of the
reel support plate (

Figure 25

).

Note:

Insert the pry bar between the top of the

reel shaft and the backs of the reel blades so
that the reel does not move.

Important:

Do not contact the cutting edge

of any blades with the pry bar; this may
damage the cutting edge and/or cause a high
blade.

Important:

The insert on the left side of

the cutting unit has left-hand threads. The
insert on the right side of the cutting unit has
right-hand threads.

g280339

Figure 25

1.

Threaded insert for
removal

3.

Weld side of reel support
plate

2.

Reel shaft

4.

Pry bar

4.

Rest the handle of the pry bar against the roller.

5.

Complete the removal of the threaded insert
while ensuring that the pry bar stays in place,
then remove the pry bar.

6.

Lower the cutting unit to rest on the rollers.

12

 

Содержание 04650

















Отзывы: