background image

inadequate braking;

the type of machine is unsuitable for its
task;

lack of awareness of the effects of ground
conditions, especially slopes;

##incorrect hitching and load distribution.

Preparation

1.

While mowing, always wear substantial footwear
and long trousers. Do not operate the equipment
when barefoot or wearing open sandals.

2.

Thoroughly inspect the area where the equipment is
to be used and remove all objects which may be
thrown by the machine.

3.

WARNING—Petrol is highly flammable.

Store fuel in containers specifically designed
for this purpose.

Refuel outdoors only and do not smoke while
refueling.

Add fuel before starting the engine. Never
remove the cap of the fuel tank or add petrol
while the engine is running or when the engine
is hot.

If petrol is spilled, do not attempt to start the
engine but move the machine away from the
are of spillage and avoid creating any source of
ignition until petrol vapors have dissipated.

Replace all fuel tanks and container caps
securely.

4.

Replace faulty silencers.

Operation

1.

Do not operate the engine in a confined space where
dangerous carbon monoxide fumes can collect.

2.

Mow only in daylight or in good artificial light.

3.

Before attempting to start the engine, disengage all
blade attachment clutches and shift into neutral.

4.

Do not use on slopes of more than:

Never mow side hills over 5°

Never mow uphill over 10°

Never mow downhill over 15°

5.

Remember there is no such thing as  a “safe” slope.
Travel on grass slopes requires particular care. To
guard against overturning:

do not stop or start suddenly when going up or
downhill;

engage the clutch slowly, and always keep the
machine in gear, especially when travailing
downhill;

machine speeds should be kept low on slopes
and during tight turns;

stay alert for bumps and hollows and other
hidden hazards;

never mow across the face of the slope, unless
the lawn mower is designed for this purpose.

6. Use care when pulling loads or using heavy

equipment.

Use only approved drawbar hitch points.

Limit loads to those you can safely control.

Do not turn sharply. Use care when reversing.

Use counterweight(s) or wheel weights when
suggested in the instruction handbook.

7. Watch out for traffic when crossing or near

roadways.

8. Stop the blades rotating before crossing surfaces

other than grass.

9. When using any attachments, never direct discharge

of material toward bystanders nor allow anyone
near the machine while in operation .

10. Never operate the lawn mower with defective

guards, shields or without safety protective devices
in place.

11. Do not change the engine governor settings or

overspeed the engine. Operating the engine at

3

Safety Instructions

Содержание 02000 GROUNDS PRO 2000





































Отзывы: