Tornatech GFX Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 46

Tornatech GFX Скачать руководство пользователя страница 45

45

Alarm Contacts Connections:

Fire Pump Controller

Motor Run connected?                                  _____Yes                _____ No

Power Available connected?                         _____Yes                _____ No

Phase Reversal connected?                         _____Yes                _____ No

Other contacts supplied and connected?     _____Yes                _____ No

Tornatech Controller S/N:              _________________________________________

Installation address:                       _________________________________________

                         _________________________________________

Field Acceptance Test completed?        _____Yes         _____ No

Field Acceptance completed by:             __________________________________________

Company:                                               __________________________________________

Date:                                                       __________________________________________

Witnessed By:                                      __________________________________________

Company:                                               __________________________________________

The undersigned witness has been made aware of the NFPA20 article 14.4 Periodic Inspection, Testing and
Maintenance which stipulates that “Fire pumps shall be inspected tested and maintained in accordance with
NFPA25

– Standard for the Inspection, Testing and Maintenance of Water Based Fire Protection Systems”

Comments:    _____________________________________________________________________________

         _____________________________________________________________________________

         _____________________________________________________________________________

         _____________________________________________________________________________

          _____________________________________________________________________________

«
...
43
44
45
46
»

Содержание GFX















































Отзывы:

Нет отзывов