manualshive.com logo in svg

Tornatech GFX, Руководство по установке и обслуживанию, Страница: 18 / 46

Поделиться
Скачать
Tornatech GFX Скачать руководство пользователя страница 18

 

 

18 

 

 

Home (Membrane button) 

Home 

 

The home page displays all controller statuses and important values of the controller. All voltages, currents, 
pressure, motor state and status, as well as all timers and motor starting sequences. 
 
The entire background will become red if an alarm becomes active. This feature will help the user identify a problem 
even from a significant distance away from the controller. 
 
A:  Navigation bar which contains general information about: 
- The language (the language may be changed by pressing on it)  
- The page title 
- The alarm banner (warning and alarm messages may be shown) 
- The date and time (adjustable in the Configuration page) 
  
B: Voltages. Each box represents an individual phase voltage between the two adjacent lines. 
 
C: Current. Each box represents an individual phase current between the two adjacent lines. 
 
D: The motor contactors are represented here. An animation shows the contactor opened or closed depending on 
the signal sent to the main coil. 
 
E: The electric motor. It will be grey if the engine is stopped, green if a “Motor Run” signal is detected and red if a 
“Fail to start” occurred. Pressing on the engine will redirect the user to the “Last Service Statistics” page, which 
monitors all relevant statistics concerning the controller since the last service. 
 
F: Timers. Sequential start timer (on-delay) will start counting upon a pressure drop. The motor will only start if the 
pressure is still below the start point after the expiration of this timer. The minimum run period timer (off 

–delay) for 

automatic shutdown will start counting once the stop pressure is reached. The pump will stop at the expiration of 
this timer if the pressure is still above the stop pressure. If a periodic test has been programmed, the remaining time 
will be displayed. If a manual run test has been energized, the remaining time will be displayed. 
 
G: The alarm/warning notification. 
Warning indicator: Exclamation mark in a yellow round icon. If no alarm is in ACTIVE condition on the controller and 
at least one warning is ACTIVE or OCCURRED, the warning indicator will be present.  
 
 

Home 

Содержание GFX















































Отзывы:

Нет отзывов