Tornatech GFX Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 46

Tornatech GFX Скачать руководство пользователя страница 36

36

History (Membrane button)

History

Select a specific page within the History section. Everything related to the statistics, events, pressure, power logs
and the download to USB is available within the History page.

-

Events: This button leads to the “Events” page, which displays the most recent 500 events. Each event log

contains the date and time of occurrence as well as a brief description of the event.

-

Download to USB Device: This button leads to the “Download to USB Device” page, which allows the user to

download information, including the user manual, drawings, logs, statistics and configuration.

-All Time Statistics: This button leads

to the “All Time Statistics” page, which displays the date and time of the first

power up, the date and time when the first start-

up was completed and the total “On Time” of the controller. These

statistics can never be reset.

-Pressure: This button leads

to the “Pressure Curves” page, which displays all relevant pressure information.

History

«
...
34
35
36
37
38
...
»

Содержание GFX















































Отзывы:

Нет отзывов