Torin QJY240C Скачать руководство пользователя страница 8

Страница: 8 / 34

Safety Requirements

DO NOT operate or repair this equipment without reading this manual. Failure to comply with these

Instructions can result in serious bodily harm and void product warranty. Make sure you have extra help or heavy

duty lifting equipment when unloading and assembling the lift. Please read the safety procedures and operating

instructions in this manual before installing or operating the equipment. Keep this manual near lift at all times.

Make sure all operators read this manual.

Manufacturer will assume no liability for loss or damage of any kind, expressed or implied resulting from

improper installation or use of this product. Do not attempt to install equipment unless you have been trained on

installation procedures. Never attempt to lift components without proper lifting tools such as forklift or cranes.

Stay clear of any moving parts that can fall and cause injury.

Safety Sticker Identification

Use care when identifications and markings are on lift. These identification are put in place to help with your

safety and the safety of others. Always use caution when working around vehicle lift.

Содержание QJY240C



































Результаты поиска

Содержание QJY240C

Отзывы:

Похожие инструкции для QJY240C

Бренды по названию

Популярные бренды

Torin QJY240C, Инструкция по эксплуатации

Результаты поиска

Содержание QJY240C

Отзывы:

Похожие инструкции для QJY240C

Бренды по названию

Популярные бренды