Torin BIG RED JACKS T30306 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 48

background image

Page

17

of

48

7.

Replace oil plug.

8.

Perform the Air Purge Procedure.

ADDITIONAL WARNINGS:

▪

DO NOT USE MOTOR OIL IN THE JACK.

▪

ONLY USE ANTI-FOAMING JACK OIL.

▪

ALWAYS USE A GOOD GRADE HYDRAULIC JACK OIL.

▪

DO NOT USE HYDRAULIC BRAKE FLUID, ALCOHOL, GLYCERINE, DETERGENT, MOTOR OIL OR
DIRTY OIL.

▪

USE OF A NON-RECOMMENDED FLUID CANCAUSE DAMAGE TO A JACK.

▪

AVOID MIXING DIFFERENT TYPES OF FLUID AND NEVER USE BRAKE FLUID, TURBINE OIL,
TRANSMISSION FLUID, MOTOR OIL OR GLYCERIN. IMPROPER FLUID CAN CAUSE PREMATURE
FAILURE OF THE JACK AND THE POTENTIAL FOR SUDDEN AND IMMEDIATE LOSS OF LOAD.

▪

DISPOSE OF HYDRAULIC FLUID IN ACCORDANCE WITH LOCAL REGULATIONS.

Additional Jack Notes:

▪

Periodically check the pump piston and ram for signs of rust or corrosion. Clean as needed and wipe
with an oil cloth. NEVER USE SANDPAPER OR ABRASIVE MATERIAL ON THESE SURFACES!

▪

When not in use, store the jack with pump piston and ram fully retracted.

FLAT BASE LONG RAM JACK

«
...
15
16
17
18
19
...
»

Содержание BIG RED JACKS T30306

















































Отзывы:

Нет отзывов

Похожие инструкции для BIG RED JACKS T30306

Бренд: ATD Tools Страницы: 12

Бренд: K Tool International Страницы: 14

Бренд: King Tony Страницы: 4

Бренд: Jegs Страницы: 4

Бренд: K-Tool Страницы: 16

Бренд: Meganex Страницы: 8

Бренд: Jefferson Страницы: 12

Бренд: Omega Lift Страницы: 8

Бренд: Clarke Страницы: 12

Бренд: ATD Tools Страницы: 8

Бренд: ATD Tools Страницы: 4

SwiftLift ATD-7325

Бренд: ATD Tools Страницы: 8

Бренд: Certa Страницы: 2

Бренд: Metal Works Страницы: 4

Бренд: RightHand Страницы: 3

Бренд: Atlas Equipment Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды