manualshive.com logo in svg

Torin BIG RED JACKS T30306, Руководство пользователя

Поделиться
Скачать
Torin BIG RED JACKS T30306 Скачать руководство пользователя страница 23

Page 

23

 of 

48

 

 

BEFORE USE 

5. 

Before using this product, read the owner's manual completely and familiarize yourself thoroughly with 
the product and the hazards associated with its improper use. 

6. 

Perform the air purge procedure. (See previous instructions for system purge procedure.) 

7. 

Check and that the pump operates smoothly before putting into service.   

8. 

Inspect before each use. Do not use if bent, broken or cracked components are noted. 

 

OPERATION 

RAISING THE JACK   

6.  Position the jack near desired lift point. 

7.  Assemble the handle, ensuring that handle aligns with handle socket. 

8.  Close the release valve by turning it clockwise until it is firmly closed. 

 

9.  Before raising check and verify the load is centered and also has full contact with the lifting point.   

10.  Pump handle to lift to desired lifting height. After lifting, support the load appropriately before starting 

work.   

 

   

 

 

CLEVIS BASE LONG RAM JACK 

Содержание BIG RED JACKS T30306

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды