manualshive.com logo in svg

Torin BIG RED JACKS T30306, Руководство пользователя

Поделиться
Скачать
Torin BIG RED JACKS T30306 Скачать руководство пользователя страница 5

Page 

5

 of 

48

 

 

Always follow safety precautions when installing and operating this jack. Keep all decals on the unit 

clean and visible. Before proceeding ensure that you fully understand and comprehend the full contents 

of this manual. Failure to operate this equipment as directed may cause injury or death. The distributor 

is not responsible for any damages or injury caused by improper use or neglect. 

 
 
 
 
 
 
 

   

  WARNING: 

Always use Jack Stands! 

DO NOT USE 

wood blocks or any other non-approved load sustaining devices. The manufacturer only 

warrants loads to be sustained by jack stands that meet current ASME standards. 

DO NOT USE 

wood blocks or any other non-approved lifting devices for a means of lifting with the jack 

and or load being raised. Failure to head these warnings may cause injury or death. 

 

 

  WARNING: 

1.  Study, understand, and follow all instructions before operating this device. 
2.  Do not exceed rated capacity. 
3.  Use only on hard, level surfaces, with less than 3 degrees of slope. 
4.  Lifting device only. Immediately after lifting, support the vehicle with appropriate means. 
5.  Do not move or dolly the vehicle while on the jack. 
6.  Lift only on areas of the vehicle as specified by the vehicle manufacturer. 
7.  No alterations shall be made to this product. 
8.  Only attachments and/or adapters supplied by the manufacturer shall be used. 
9.  Do not get under or allow anyone under the vehicle until it has been supported by jack stands. 
10. Center load on saddle prior to lifting. 
11. Use wheel chocks or other blocking device on opposing wheels before using jack. 
12. Never use on a lawn mower or lawn tractor. 
13. Do not use this jack for any use other than the manufacturer specified usage. 
14. Do not rock the vehicle while working on or around equipment. 
15. The following are not recommended for supporting on this equipment: Foundations, Homes, 

Mobile 

Homes, Trailers, RV’s, Campers, nor Fifth Wheels, etc... 

16. Failure to heed these markings may result in personal injury and/or property damage. 

 

 

SAFETY 

THIS IS A LIFTING DEVICE ONLY! 

• This jack is designed only for lifting part of the total vehicle. 
• Do not move or dolly the vehicle while on the jack. 
• The vehicle must be supported after lifting immediately by appropriately rated jack stands. 
• NEVER go under a vehicle that is not supported with appropriately rated jacks stands. 
• Use wheel chocks or other blocking device on opposing wheels before using jack stands. 

SAFETY MARKINGS 

Содержание BIG RED JACKS T30306

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды