Toray 050-1F Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 69

Toray 050-1F Скачать руководство пользователя страница 64

TORAY MBR

Instruction Manual

06-G-MB2-NHPAF-220801

59 of 63

Keep the membranes wet once they get wet. If the membranes are

allowed to dry out, the permeability of the membranes may be

permanently reduced.

10. Disposing Procedure

Follow these general guidelines when disposing of the membrane after use.

(1) Clean the membrane module with clean water. After the module has been rinsed off,

allow the surfaces to dry. Dry surfaces make handling and transport easier.

(2) Dispose of the module or module components according to local waste disposal

regulations. If required, disassemble the module and segregate its components
accordingly (e.g. combustible/incombustible).

(3) Do not incinerate the membrane unless appropriate facilities are available. During the

incineration of the membrane materials,  harmful Hydrogen Fluoride (HF) gas will be
generated. If the membranes are to be incinerated,  it is recommended  that a
professional waste disposal company be hired for the disposal.

Do not burn the membranes without appropriate facilities since

harmful Hydrogen fluoride (HF) gas will be generated. Hire a

professional solid waste disposal company to perform the task

when disposing of the membrane elements.

CAUTION

!

WARNING

!

«
...
62
63
64
65
66
...
»

Содержание 050-1F






































































Отзывы:

Нет отзывов