background image

TORAY MBR 

 

Instruction Manual 

 

06-G-MB2-NHPAF-220801

 

48  of 63 

(e)  Thoroughly  wash your hands and face and rinse out your mouth after using 

chemicals. 

(f)  Do not eat or drink anything in the working place except in a designated place. 
(g)  Do not bring gloves or other contaminated protectors into the rest area. 
(h)  Forbid unauthorized entry to the place where chemicals are handled. 
(i)  Wear appropriate protectors to avoid inhalation, eye or skin contact, and direct 

contact with your clothes. 

(j)  Provide local ventilation in the case of handling chemicals indoors.   

 

(B)  Storage Precautions 

(a)  Store the container in a dark, cold place. Avoid direct sunlight. Firmly seal to 

prevent direct contact with air. 

(b)  Use corrosion-resistant containers for storage. 

 
(3)  Citric Acid / HOOCCH

2

C(OH)(COOH)CH

2

COOH 

(A)  Handling Precautions 

(a)  Keep away from strong oxidants and bases.   
(b)  Handle the chemical  container with great care. Avoid toppling, bumping,  or 

dragging it. 

(c)  Take care not to spill liquid chemicals and avoid breathing in vapors. In the 

case of dry chemical powders, handle in a manner that minimizes the formation 
of chemical dust.   

(d)  Securely seal all chemical containers after each use. 
(e)  Thoroughly  wash your hands and face and rinse out your mouth after using 

chemicals. 

(f)  Do not eat or drink anything in the working place except in a designated place. 
(g)  Do not bring gloves or other contaminated protectors into the rest area. 
(h)  Forbid unauthorized entry to the place where chemicals are handled. 
(i)  Wear appropriate protectors to avoid inhalation, eye or skin contact, and direct 

contact with your clothes. 

(j)  Provide local ventilation in the case of handling chemicals indoors. 
 

(B)  Storage Precautions 

(a)  Store the container in a dark, cold place. Avoid direct sunlight. Firmly seal to 

prevent direct contact with air. 

(b)  Use corrosion-resistant containers for storage. 

 
 
 

Содержание 050-1F






































































Отзывы: