Topcon System 350 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 112

background image

X30 Spreader Controller

0-5

Communications Regulation Information

FCC Compliance Statement (USA)

This equipment has been tested and found to comply with
the limits for a Class ‘A’ digital device, pursuant to Part
15 of the FCC Rules. Operation of this equipment in a
residential area is likely to cause harmful interference in
which case the user will be required to correct the
interference at the user's expense.

FCC Compliance Statement (Canada)

This Class A digital apparatus meets all requirements of
the Canadian Interference-Causing Equipment
Regulation.

CE EMC Statement (European Community)

Warning: This is a class ‘A’ product. In a domestic
environment this product may cause radio interference in
which case the user may be required to take adequate
measures.

‘C’ Tick EMC Statement (Australia & New Zealand)

This product meets the applicable requirements of the
Australia and New Zealand EMC Framework.

Type Approval and Safety Regulations

Type approval may be required in some countries to license the
use of transmitters on certain band frequencies. Check with local
authorities and your dealer. Unauthorized modification of the
equipment may void that approval, the warranty and the license to
use the equipment.

The receiver contains internal radio-modem. This can potentially
send signals. Regulations vary between countries, so check with
the dealer and local regulators for information on licensed and
unlicensed frequencies. Some may involve subscriptions.

«
...
6
7
8
9
10
...
»

Содержание System 350

















































































































Отзывы:

Нет отзывов

Похожие инструкции для System 350

Бренд: Danfoss Страницы: 32

PVG 16 PVH/Covers

Бренд: Danfoss Страницы: 112

Бренд: Danfoss Страницы: 44

PVG 16 PVH/Covers

Бренд: Danfoss Страницы: 144

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 64

Бренд: Danfoss Страницы: 8

VLT AutomationDrive FC 360

Бренд: Danfoss Страницы: 60

Бренд: Danfoss Страницы: 6

Бренд: Danfoss Страницы: 4

Бренд: Danfoss Страницы: 8

Бренд: Danfoss Страницы: 2

ECL Comfort 110

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 24

Бренд: National Instruments Страницы: 29

Бренд: M-Audio Страницы: 26

Бренд: M Climate Страницы: 12

Бренд: Zennio Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды