Topcon System 350 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 112

background image

X30 Spreader Controller

0-3

warrants that all valves, hoses, cables

and mechanical parts manufactured

by TPA shall be free of defects in

materials and workmanship for a

period of one year from the date of

purchase.

RETURN AND REPAIR

- During

the respective warranty periods, any

of the above items found defective

may be shipped to TPA for repair.

TPA will promptly repair or replace

the defective item at no charge, and

ship it back to you. You must pay the

shipping and handling charges in

respect of the same. Calibration of

components, labor and travel

expenses incurred for in-field

removal and replacement of

components are not covered in this

warranty policy. The foregoing

warranty shall NOT apply to damage

or defects resulting from:
(i) disaster, accident or abuse
(ii) normal wear and tear
(iii) improper use and/or

maintenance

(iv) unauthorized modifications of

the product; and/or

(v) use of the product in

combination with other products

not supplied or specified by

TPA.

Software accompanying any product

is licensed for use in connection with

the product and not sold. Use of

software that is provided with a

separate end user license agreement

(“EULA”) will be subject to the

terms and conditions, including those

relating to limited warranty, of the

applicable EULA, notwithstanding

anything in these Terms and

Conditions to the contrary.

WARRANTY DISCLAIMER

-

OTHER THAN FOR THE ABOVE
WARRANTIES, WARRANTIES
PROVIDED IN AN APPLICABLE
WARRANTY CARD, APPENDIX
OR END USER LICENSE
AGREEMENT, THIS MANUAL,
THE PRODUCT AND RELATED
SOFTWARE ARE PROVIDE ‘AS-
IS’. THERE ARE NO OTHER
WARRANTIES AND TO THE
EXTENT ALLOWED BY LAW TPA
EXCLUDES ALL IMPLIED
TERMS, CONDITIONS AND
WARRANTIES IN RESPECT OF
THE MANUAL AND THE
PRODUCT (INCLUDING ANY
IMPLIED WARRANTY OR
MERCHANTABILITY OR
FITNESS FOR ANY PARTICULAR
USE OR PURPOSE). TPA IS NOT
RESPONSIBLE FOR THE
OPERATION OF GNSS
SATELLITES AND/OR
AVAILABILITY, CONTINUITY,
ACCURACY, OR INTEGRITY OF
GNSS SATELLITE SIGNALS.

LIABILITY LIMIT AND
INDEMNITY

-

TPA and its dealers,

agents and representatives shall not

be liable for technical or editorial

errors or omissions contained herein

or for special, indirect, economic,

incidental or consequential damages

resulting from the furnishing,

performance or use of this material,

the product or its accompanying

software (including where TPA has

been advised of the possibility of

such damage). Such disclaimed

damages include but are not limited

to loss of time, loss or destruction of

data, loss of profit, savings or

revenue or loss of or damage to the

product. You shall defend,

indemnify and hold TPA harmless

from and against any claims, actions,

suits, damages, losses, liabilities and

«
...
4
5
6
7
8
...
»

Содержание System 350

















































































































Отзывы:

Нет отзывов

Похожие инструкции для System 350

Бренд: Eaton Страницы: 50

DELTAFLUX MT100

Бренд: PIETRO FIORENTINI Страницы: 16

Бренд: Zetkama Страницы: 6

Бренд: Facility Explorer Страницы: 4

Бренд: Sole Diesel Страницы: 8

Бренд: DAV TECH Страницы: 10

Бренд: C.Nord Страницы: 100

CoreBuilder 9000

Бренд: 3Com Страницы: 78

Бренд: HABONIM Страницы: 9

Бренд: Fuji Electric Страницы: 12

Бренд: heat-timer Страницы: 36

Optidrive Elevator

Бренд: Invertek Страницы: 5

Бренд: Techtrol Страницы: 4

Бренд: nvent Страницы: 4

ZoneSense Plus AS

Бренд: Halma Страницы: 58

Бренд: Acumen Страницы: 6

Бренд: PCB Piezotronics Страницы: 12

Бренд: Skov Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды