Topcon System 350 Скачать руководство пользователя страница 5

Страница: 5 / 112

X30 Spreader Controller

0-2

Terms and Conditions

Please read these Terms and Conditions carefully.

General

APPLICATION

- You accept these

Terms and Conditions by purchasing

the product from Topcon Precision

Agriculture (TPA) or from one

TPA’s product dealers.

COPYRIGHT

- All information

contained in this manual is the

intellectual property of, and

copyrighted material of TPA. All

rights are reserved. You may not use,

access, copy, store, display, create

derivative works of, sell, modify,

publish, distribute, or allow any third

parties access to, any graphics,

content, information or data in this

manual without TPA’s express

written consent and may only use

such information for the care and

operation of your product. The

information and data in this manual

are a valuable asset of TPA and are

developed by the expenditure of

considerable work, time and money,

and are the result of original

selection, coordination and

arrangement by TPA.

TRADEMARKS

– ZYNX,

PROSTEER, EAGLE, KEE

Technologies, Topcon, Topcon

Positioning Systems and Topcon

Precision Agriculture are trademarks

or registered trademarks of the

Topcon Group of companies.

Microsoft and Windows are

trademarks or registered trademarks

in the United States and/or other

countries of Microsoft Corporation.

Product and company names

mentioned herein may be trademarks

of their respective owners.

WEBSITE AND OTHER
STATEMENTS

- No statement

contained at the website of TPA or

any other Topcon Group company or

in any other advertisements or TPA

literature or made by an employee or

independent contractor of TPA

modifies these Terms and

Conditions.

IMPORTANT: SAFETY

- Improper

use of the product can lead to death

or injury to persons, damage to

property and/or malfunction of the

product. The product should only be

repaired by authorized TPA service

centers. You should closely review

the safety warnings and directions as

to the proper use of the product in

this manual and at all times comply

with the same.

Limited Warranty

ELECTRONIC AND
MECHANICAL COMPONENTS

TPA warrants that the electronic

components manufactured by TPA

shall be free of defects in materials

and workmanship for a period of one

year from the original date of

shipment to the dealer. TPA

Содержание System 350

















































































































Результаты поиска

Содержание System 350

Отзывы:

Похожие инструкции для System 350

Бренды по названию

Популярные бренды

Topcon System 350, Руководство оператора

Результаты поиска

Содержание System 350

Отзывы:

Похожие инструкции для System 350

Бренды по названию

Популярные бренды