Topcon System 350 Скачать руководство пользователя страница 109

Страница: 109 / 112

X30 Spreader Controller

A-1

Appendix – Start up Checklist



Read safety information.



Drive to the working area.



Turn the X30 Console on.



Select vehicle and implement, if necessary. System may
restart.



Have the necessary system features been enabled?



Has the field been selected?



If it is a new field, has the boundary been set?



Select the Guidance Line to be used or create a new one.



Create a new job if data is to be recorded and saved.



Are Spreader and Auto Section Control icons in the
Navigation Bar?



Has calibration been completed?



Is the speed source set correctly? Remember that Manual
Speed Source will override many automatic features.



Select the Bin Control icon.



Are Bin settings correct (product selected, bin filled)?



Are Preset Rates correct?



Turn on the Bin Control.



Set a Sub Area if needed.



If using Variable Rate Control, select the VRC
prescription map file.



Select Auto Control Rate or Variable Control Rate
spreading mode.



Is the Spreader Master Switch white? If not, select the
icon to identify the problem.



Start spinners and bring up to speed.

Содержание System 350

















































































































Результаты поиска

Содержание System 350

Отзывы:

Похожие инструкции для System 350

Бренды по названию

Популярные бренды

Topcon System 350, Руководство оператора

Результаты поиска

Содержание System 350

Отзывы:

Похожие инструкции для System 350

Бренды по названию

Популярные бренды