1)
Enter the
P
key
2)
Enter your new (or default) Passcode:
x
x
x
x
3)
Wait until the LED displays “P”
4)
Enter the
9
key (Command Code for this function)
5)
Enter
0
~
9
(This number will be automatically multiplied by 2 for the actual amount
of minutes. For example, 8 will actually equal 16 minutes) depending on the length of
time you want the siren to sound (Entering “0” turns the Siren feature off)
6)
You will hear a confirmation tone, and the information is stored (One long beep =
correct entry / Three quick beeps = incorrect entry must be re-entered)
Step 6 – Program Remote Call-In Ring Cycle (Default: 6 Rings)
This function is for users to program the amount of rings before the system picks up during a
Remote Call-In (calling in to system from anywhere in the world to arm, disarm, monitor or
speak). The factory default is 6 rings, but you can program up to 9 rings.
1)
Enter the
P
key
2)
Enter your new (or default) Passcode:
x
x
x
x
3)
Wait until the LED displays “P”
4)
Enter the
0
key (Command Code for this function)
5)
Enter
0
~
9
depending on the amount of rings you want before the system
automatically picks up
NOTE:
Entering “
0
“ will turn the Remote Call-In feature to
OFF
.
6)
You will hear a confirmation tone, and the information is stored (One long beep =
correct entry / Three quick beeps = incorrect entry must be re-entered)
Step 7 – Site Code Learning from Pocket Remote Control
This function allows the Control Panel to “learn” the security system Site Code from the Remote
Control. The Remote Control must be set with the master code, and all other detectors must be
set with the same Site Code as the Pocket Remote. It is best to use the factory default setting
unless absolutely necessary (See “Advanced Programming”).
Please note:
Remote Control is the only component in the system for Site Code learning.
1)
Enter the
L
key
2)
Enter your new (or default) Passcode:
x
x
x
x
3)
Wait until the LED displays “L”
4)
Enter the
#
key (Command Code for this function)
5)
Push any button on the Pocket Remote
6)
You will hear a confirmation tone, and the information is stored (One long beep =
correct entry / Three quick beeps = incorrect entry must be re-entered)
Step 8 – Ring Back Tone Learning
This function allows the Control Panel to “learn” the unique telephone ring back specific to user’s
country or locale. This is a very simple procedure, but it is extremely important to the entire
operation of the Auto-Dialer feature.
1)
Make sure that a telephone number has been programmed into phone number
position 1 before beginning this procedure
2)
Make sure that the person on the other end of that telephone number
DOES NOT
pick up the telephone during this procedure
3)
Enter the
L
key
4)
Enter your new (or default) Passcode:
x
x
x
x
5)
Wait until the LED displays “L”
6)
Enter the
Ý
key (Command Code for this function)
7)
The system will dial the telephone number in position 1 automatically
8)
The system will emit one beep tone to confirm that the Ring Back Tone Learning has
been completed successfully / Three quick beeps = incorrect entry must be re-entered.
Step 9 – Record Alarm Notification Message
This function is for users to record the Alarm Notification Message that will play during an Alarm
Notification Call. The total recording time is 20 seconds.
It is best to use this message to notify that there has been an alarm activation, and also to specify
exactly how the call recipient can respond (listen in, monitor, speak, control auto-dialing or replay
message). The following script can be used as a guide on how to word your message. Make
sure that you speak clearly and steadily, approximately ten inches from the microphone. Keep
in mind that you have exactly 20 seconds of recording time.
Message Script suggestion:
“This is (your name). An alarm has been activated at (address). After the tone, press 4 to listen,
5 to speak, 6 to dial next number, 7 to replay this message, and 8 to stop dialing and disconnect.”
1)
Enter the
P/R
key
2)
Enter your new (or default) Passcode:
x
x
x
x
3)
Wait until the LED displays “
├
”
4)
Enter the
#
key (Command Code for this function)
5)
Begin recording the message for up to 20 seconds
6)
At the end of the 20 seconds you will hear a confirmation tone, and the message is stored
(One long beep = correct entry / Three quick beeps = incorrect entry must be re-entered)
*To replay the message, repeat steps 1, 2 and 3, then enter
Ý
to hear the message.
