Using Remote Control–
1)
Press the
MODE
button on the Remote Control
2)
You will hear three chirps as a confirmation, and the setting is accomplished
Using the keypad on the Control Panel –
1)
Enter the
S
key
2)
Enter your new (or default) Passcode:
x
x
x
x
(One beep = correct entry / Three quick beeps = incorrect entry must be re-entered)
3)
Wait until the LED displays “S”
4)
Enter the
0
key (Command Code for this function)
5)
After the confirmation tone you will hear three beeps, and the setting is accomplished
Enter Emergency/Panic Alarm
This function is used to activate the alarm during an on-site emergency or panic situation.
Using Remote Control–
1)
Press the
PANIC
button on the
Remote Control
2)
The system will immediately activate the alarm, sound the siren and immediately
begin dialing the programmed phone numbers
Using the keypad on the Control Panel –
1)
Press the
PANIC
button on the control panel.
2)
The system will immediately activate the alarm, sound the siren and immediately
begin dialing the programmed phone numbers
NOTE:
This button can also be used to enter a 2-way speakerphone call during an
incoming phone call (
never to be used for outgoing phone calls, doing so will
activate the alarm “Panic”
).
Enter Test Mode (Battery Change Mode)
This function is used to test the entire system (all Zones) and all sensors/detectors, ensure that
the sensors/detectors are installed within wireless range of the Control Panel, and that they are
working properly. This is also used for “Battery Change” as the tamper switches are disabled
thus allows detector covers to be removed to replace batteries.
NOTE:
Testing of your system should be done on a regular basis to ensure that the system and
the sensors/detectors are working properly. This will also help you to gain a better understanding of
the capabilities of the system, and should help to eliminate any malfunction during a crisis situation.
To Enter Test Mode using the keypad on the Control Panel –
1)
Enter the
S
key
2)
Enter your new (or default) Passcode:
x
x
x
x
(One beep = correct entry / Three quick beeps = incorrect entry must be re-entered)
3)
Wait until the LED displays “S”
4)
Enter the
Ý
key (Command Code for this function). You will hear a “ding dong” as
confirmation.
5)
Activate each of the sensors/detectors (one at a time)
6)
The Control Panel will emit beep sounds as each detector is activated to confirm proper
operation. The number of beeps indicates the corresponding Zone of the sensor/detector.
NOTE:
A doorbell sound indicates a low battery in the sensor/detector. This function
is also useful to identify which of the sensors set to the same zone has a low battery.
To Exit Test Mode
(and enter Disarming Mode) using the keypad on the Control Panel:
1)
Enter the
S
key
2)
Enter your new (or default) Passcode:
x
x
x
x
(One beep = correct entry / Three quick beeps = incorrect entry must be re-entered)
3)
Wait until the LED displays “S”
4)
Enter the
0
key (Command Code for this function)
5)
After the confirmation tone you will hear three beeps, and the setting is accomplished
Responding During an Alarm Notification Call
This function is used for call recipients to respond to an Alarm Notification Call. Call recipients
will have the option to monitor/listen in (via built-in microphone on Control Panel), speak (via
built-in 2-way speakerphone feature), have the system hang up and dial the next programmed
phone number, have the system stop dialing all programmed phone numbers, or replay the
Alarm Notification Message. This can all be accomplished by pressing specified keys on any
telephone keypad, from anywhere in the world.
Upon an alarm activation, the Auto-Dialer will call out to each of the programmed phone numbers
and play the Alarm Notification Message (as recorded by user). The call recipient’s procedure
and options are as follows:
1)
Answer the call, then wait for the pre-recorded Alarm Notification Message to finish playing
2)
Within 10 seconds after you hear the confirmation tone, press a key for the desired
function as follows:
•
Press
4
to Monitor/Listen in
•
Press
5
to Speak via 2-way Speakerphone
•
Press
6
to have system Hang Up and Dial Next Programmed Phone Number
•
Press
7
to Replay the Alarm Notification Message
•
Press
8
to have system Stop Dialing all Programmed Phone Numbers and
Disconnect Call
Remote Access from Any Outside Telephone
This function allows users to call in from anywhere in the world to access the system. Users calling
in will have the ability to enter the system into Full Arming Mode or Disarming Mode, as well as
monitor/listen in (via built-in microphone on Control Panel) or speak (via built-in 2-way speakerphone
feature). This can all be accomplished by pressing specified keys on any telephone keypad,
while calling in from anywhere in the world.
