Toku TMH-25TP2E/C2 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 37

Toku TMH-25TP2E/C2 Скачать руководство пользователя страница 11

10

WARNING

;

When using 2-load suspension type, be sure to use sling chain or

wire style equipment when lifting.

・

When lifting a load using an under hook 2-load suspension type(TMH-6000-2), be sure to use a

sling chain or wire style equipment and be sure to lift the center of the load with under hook in

vertical position. Please do not tilt or drag the under hook when lifting.

If the load is lifted wrong way, there is a possibility that under hook block will tilt or the chain will

loosen.

This may allow the limit spring on the chain to enter the chain entrance in the under

hook and jam, or the chain can get hung up and may lead to chain breakage or an accident.

When lifting the load, make sure the chain can move smoothly into the under hook block entry

holes.

WARNING

;

Lubrication for the chain.

・

Please apply lubrication oil to the lifting chain certainly. If there is no oil on the chain, chain will be
worn out soon. This may lead to dropping of the load and personal injury due to breaking of the
chain and it is very dangerous.

Lubricate chain links and sprockets contacting part on both Load Sheave and Free Chain Wheel
with Fricttle 2 (liquid type, Rix Corporation product) in every 300 cycles. Make sure to lubricate
chain when it is dry even before reaching 300 cycles. Viscogen KL300 (Castrol .Ltd product) can be
used instead of Fricttle 2 in a light use, less than 30 cycles a day. In this case lubricate chain
every 30 cycles. Spray type is recommended for easy lubricating.

CAUTION

;

Do not pull or use the hoist side ways.

・

The hoist was designed to be used in the vertical direction. Using the hoist in the horizontal

direction is not recommended and may result in an accident or premature wear of parts.

CAUTION

;

Do not suddenly change the direction of the hoist.

・

Suddenly changing the direction of the hoist will shock certain areas of the hoist and may cause

breakage of parts or lead to an accident.

CAUTION

;

Do not pull on the pendant hose or cords when trying to

move the hoist.

・

This will lead to damage to the hose and may cause the hoist to malfunction.

[email protected]

Air & Allied Sales (Pacific) Pty Ltd

www.air-allied.com.au

«
...
9
10
11
12
13
...
»

Содержание TMH-25TP2E/C2






































Отзывы:

Нет отзывов