Tohnichi CTA2-G Скачать руководство пользователя страница 20

Страница: 20 / 56

(3) Tightening operation: Example 1 (Torque tightening stage + 1

angle

tightening stage, NG_RES

）

Below instructions shows an operation flow for tightening at the following values.

Tightening torque

30 N・ｍ 2

tightening angle upper limit

95 deg

Tightening torque upper limit

35 N・ｍ 3

tightening angle

Snug torque

30 deg 3

tightening angle upper limit

tightening angle

90 deg Number of spindle

5 pc

tightening angle upper limit

95 deg NG setting

NG_RES

tightening angle

90 deg

Operation Flow

Torque tightening stage (5 spindles)

→

angle tightening stage (5 spindles)

→

angle tightening stage (5 spindles) After completing tightening of all the stages, it
output data and proceeds to the next work.

Torque tightening stage 1

angle tightening stage 2

angle tightening stage

Completion

Tightening order
Torque tightening stage: Spindle

①

→

Spindle

②

→

Spindle

③

→

Spindle

④

→

Spindle

⑤

→

angle tightening stage: Spindle

①

→

Spindle

②

→

Spindle

③

→

Spindle

④

→

Spindle

⑤

→

angle tightening stage: Spindle

①

→

Spindle

②

→

Spindle

③

→

Spindle

④

→

Spindle

⑤

All stage complete (data output)

→

Proceed to the next work

NG setting explanation
“NG_RES”: When the judgment is NG, press MEM key to saves the data and proceed to
the next spindle.
“ALLRES”: When the judgment is NG, press MEM key to save the data. The memory

counter will be renewed and start from the beginning stage.

* In both cases, press C key to delete the data.

Содержание CTA2-G

























































Результаты поиска

Содержание CTA2-G

Отзывы:

Бренды по названию

Популярные бренды

Tohnichi CTA2-G, Инструкция по эксплуатации

Результаты поиска

Содержание CTA2-G

Отзывы:

Бренды по названию

Популярные бренды