TOHATSU V20D2 Скачать руководство пользователя страница 37

Страница: 37 / 90

ENGINE START

1. Place the pump near water source on the flat area.
2. Connect suction hose and delivery hose to the pump securely. Put the end of suction

hose in water source. The suction hose must have a strainer and a basket.

3. When the pump discharge operation will be done by a branch pipe with nozzle fitted,

recommend nozzle bore are within the range below.

Low pressure 21 mm (0.8 in) ~ High pressure 15.5 mm (0.6 in)

Over 21 mm (0.8 in) nozzle bore can cause pump damages.

Starting engine

Wear proper hearing protection during
operation.

While engine is running, do not touch the high
voltage Ignition wire attached to spark plug.
This wire carries very high voltage which will
cause injury and bodily harm.

Do not operate pump on dry grass.
The exhaust system will be very hot and will
ignite dry grass. Clear the area if necessary.

１

２

３

４

５

６

７

８

９

Содержание V20D2



























































































Результаты поиска

Содержание V20D2

Отзывы:

Бренды по названию

Популярные бренды

TOHATSU V20D2, Руководство пользователя

Результаты поиска

Содержание V20D2

Отзывы:

Бренды по названию

Популярные бренды