TM 9-1829A Скачать руководство пользователя страница 93 | Manualshive

Страница: 93 / 100

TM 9-1829A Скачать руководство пользователя страница 93

TM 9-1829A, April 1944

93/100

2021-07-07

c.

Replace gear

(D): Place washer over gear end of driven shaft and place shaft in sleeve. Place another washer

over shaft and start gear (D) onto shaft. Place special tool (T-178708 Det. 1 and 5) and assembly in vise, and
press gear on shaft (fig. 146) until there is about 0.001 inch end play in shaft. Remove from vise and check
end play and test for free turning.

Figure 146: Pressing gear (D), on shaft, using adapter tool (T-178708 Det. 1 and 5)

d.

Replace sleeve and nut

(transmission end): Place coupling nut over sleeve and, using vise, press sleeve into

case (fig. 147) until inside end of sleeve is flush with inside of case, making sure that slot in sleeve lines up
with pin hole in case. Using small hammer, drive pin in place.

Figure 147: Pressing sleeve (transmission end) into case, using adapter tool (T-178708 Det. 3)

e.

Replace gear

(A): Place drive shaft in sleeve and start gear (A) onto shaft. Place this assembly and special

tool (T-178708 Det. 1 and 3) in vise, and press gear (A) on shaft (fig. 148). Allow about 0.005 inch end play.
Test for free turning.

Figure 148: Pressing gear (A) on shaft, using adapter tool (T-178708 Det. 1 and 3)

f.

Assemble case:

Place intermediate gear assembly in either half of case, making sure that it is in correct

position. Replace gasket. Fill both sides of drive joint with No. 00 grease, O.D. Make sure that the gears are
in mesh, bring the two halves of the drive joint together, and replace the four screws. Test for free turning.

«
...
91
92
93
94
95
...
»

Содержание 9-1829A





































































































Отзывы:

Нет отзывов