TLV PowerTrap GP10F Скачать руководство пользователя страница 2

Страница: 2 / 35

172-65378MA-03 (GP10F PowerTrap) 23 Apr 2019

Contents

Introduction ...........................................................................2

Safety Considerations ...........................................................3

General Description ..............................................................5

Application .................................................................................................................. 5

Operation ..............................................................................6

Specifications ........................................................................7

Configuration .........................................................................7

Installation .............................................................................8

Open System* Piping (Steam System Example) ......................................................... 8

Installation Procedure ................................................................................................. 9

Sizing the Condensate Receiver/Reservoir ............................................................... 12

Installing Several PowerTrap Units in Parallel ........................................................... 16

Installation and Maintenance Space ...................................17

Operation and Periodic Inspection ......................................18

Operation .................................................................................................................. 18

Periodic Inspection and Diagnosis ............................................................................ 19

Disassembly/Reassembly ...................................................21

Recommended Tools List for Disassembly/Reassembly ........................................... 22

1. Removing/Reattaching the Cover Unit .................................................................. 23

2. Removing/Reattaching the Float ........................................................................... 24

3. Removing/Reattaching the Snap-action Unit ......................................................... 24

4. Removing/Reinstalling the Exhaust Valve ............................................................. 25

5. Removing/Reinstalling the Exhaust Valve Seat ..................................................... 25

6. Removing/Reinstalling the Motive Medium Intake Valve and Valve Seat .............. 26

7. Checking/Adjusting the Gap between the Push Plate and the Motive Medium Intake

Valve ...................................................................................................................... 27

Troubleshooting ..................................................................28

Determining the Problem from the Symptoms ........................................................... 28

Types of Failure and their Causes ............................................................................ 29

Causes and Corrective Measures ............................................................................. 30

Product Warranty ................................................................33

Service ................................................................................34

Содержание PowerTrap GP10F



































Результаты поиска

Содержание PowerTrap GP10F

Отзывы:

Похожие инструкции для PowerTrap GP10F

Бренды по названию

Популярные бренды

TLV PowerTrap GP10F, Инструкция по эксплуатации

Результаты поиска

Содержание PowerTrap GP10F

Отзывы:

Похожие инструкции для PowerTrap GP10F

Бренды по названию

Популярные бренды