TLV PowerTrap GP10F Скачать руководство пользователя страница 24

Страница: 24 / 35

172-65378MA-03 (GP10F PowerTrap) 23 Apr 2019

1. Removing/Reattaching the Cover Unit

Prepare a new cover gasket for replacement before beginning this step.

Part

Disassembly

Reassembly

Drain Plug
(if present)

• Using an adjustable wrench, slowly loosen plug to release

pressure and discharge fluid; take care to avoid being
burned by fluid discharge.

• Wrap threads with 3

to 3.5 turns of sealing
tape or apply sealing
compound.

• Tighten to a torque of

30 N

⋅

m (22 lbf

⋅

ft).

Cover Bolts • Using a 19 mm (¾ in) socket wrench, loosen each bolt

slowly one turn in an alternating diagonal pattern.

• Once all bolts have been loosened, verify that there is no

internal pressure before completely removing the bolts.

• Reverse steps in

disassembly.

• Tighten to a torque of

80 N

⋅

m (58 lbf

⋅

ft)

Cover Unit

NOTE:
All internal
components
are attached
to the cover
unit

• Disconnect the motive medium supply piping and the

exhaust piping from the cover unit (utilize unions in the
piping if present).

• Make sure to secure sufficient space above the cover unit

to allow it to be lifted straight up.

• The cover unit weighs 12.7 kg (28 lb); take any

appropriate measures to assist in its removal.

• When removing the cover unit, be careful not to bang or

damage the float or other internal components.

• If disassembly of the cover unit is required, support the

cover unit securely on a rack that allows access to the
components suspended below.

• Reverse steps in

disassembly.

Cover
Gasket

• Remove gasket and clean sealing surfaces on the body

and cover.

• Replace with a new

gasket.

(1 N

⋅

≈

10 kg

⋅

cm)

Tank

Cover Gasket

Tank

Tank/Body

Cover Bolt

Cover Unit

NOTE: Configuration of tank/body may differ slightly.

Содержание PowerTrap GP10F



































Результаты поиска

Содержание PowerTrap GP10F

Отзывы:

Похожие инструкции для PowerTrap GP10F

Бренды по названию

Популярные бренды

TLV PowerTrap GP10F, Инструкция по эксплуатации

Результаты поиска

Содержание PowerTrap GP10F

Отзывы:

Похожие инструкции для PowerTrap GP10F

Бренды по названию

Популярные бренды