TLV PowerTrap GP10F Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 35

background image

172-65378MA-03 (GP10F PowerTrap) 23 Apr 2019

18

Operation and Periodic Inspection

•

After all piping work has been completed in accordance with the

specific piping system designed when the decision to utilize the

PowerTrap was made, check once again to make sure that all pipe

connections have been tightened, gaskets have been inserted where

needed and all parts are securely installed.

•

When beginning operation, make sure that the operator stays well clear

of the release area of the vent line and overflow piping.

At the start-up of operation, large quantities of condensate may flow,

causing the PowerTrap to momentarily overload. If this occurs in open

systems, hot condensate may spurt from the vent piping or overflow

piping and could result in burns, other injuries or damage to equipment.

WARNING

Install properly and DO NOT use this product outside the recommended

operating pressure, temperature and other specification ranges.

Improper use may result in such hazards as damage to the product or

malfunctions which may lead to serious accidents. Local regulations

may restrict the use of this product to below the conditions quoted.

CAUTION

When disassembling or removing the product, wait until the internal

pressure equals atmospheric pressure and the surface of the product

has cooled to room temperature. Disassembling or removing the

product when it is hot or under pressure may lead to discharge of fluids,

causing burns, other injuries or damage.

CAUTION

Be sure to use only the recommended components when repairing the

product, and NEVER attempt to modify the product in any way. Failure to

observe these precautions may result in damage to the product or burns

or other injury due to malfunction or the discharge of fluids.

CAUTION

Installation, inspection, maintenance, repairs, disassembly, adjustment and valve
opening/closing should be carried out only by trained maintenance personnel.

Operation

(1) Valve Operation

Refer to the open-system piping drawing in “Installation” on page 8 to become
familiar with the names and locations of the various valves.
If water hammer occurs, immediately cease operation and close any valves that are
operating.

a) Slowly open the valve on the exhaust pipe.

b) Slowly open the valve on the motive medium supply pipe.

Make sure that there is no sound of flow from the exhaust pipe or the pumped
medium inlet pipe.

c) Slowly open the valve on the pumped medium outlet pipe.

d) Slowly open the valve on the pumped medium inlet pipe.

When using a manual valve for venting air on a closed system, leave the valve
slightly open until the PowerTrap has cycled 2 or 3 times in order to release any
air inside the system, then close the valve.

«
...
17
18
19
20
21
...
»

Содержание PowerTrap GP10F




































Отзывы:

Нет отзывов

Похожие инструкции для PowerTrap GP10F

Бренд: Wayne Страницы: 16

Aqua-Pure AP510

Бренд: 3M Страницы: 16

Бренд: IBC Страницы: 18

Бренд: A.O. Smith Страницы: 4

Бренд: A.O. Smith Страницы: 76

Бренд: Daikin Страницы: 52

Бренд: Daikin Страницы: 147

Бренд: Daikin Страницы: 175

Бренд: York Страницы: 27

Бренд: York Страницы: 32

ROYTRONIC A Series

Бренд: LMI Страницы: 36

WILDEN P100 Advanced Plastic

Бренд: PSG Dover Страницы: 28

Waterfall Kit WFK8

Бренд: Beckett Страницы: 1

Бренд: Waterous Страницы: 10

Бренд: ProMinent Страницы: 81

OmniSpense ELITE

Бренд: Wheaton Страницы: 34

Бренд: VONROC Страницы: 60

Бренд: Debem Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды