TLV PowerTrap GP10F Скачать руководство пользователя страница 26

Страница: 26 / 35

172-65378MA-03 (GP10F PowerTrap) 23 Apr 2019

4. Removing/Reinstalling the Exhaust Valve

Part

Disassembly

Reassembly

Exhaust
Valve

• Using needle-nose pliers, remove the split pin

from one side of the connecting pin; remove the
exposed flat washer.

• Remove the connecting pin; be careful not to lose

the flat washers.

• Lift the exhaust valve off of the top of the snap-

action unit

• Reverse the steps to reassemble.
• Use a new split pin if the old one

was damaged during disassembly.

• Fold the legs of the split pin

completely so that they are wound
around the connection pin.

Exhaust
Valve

Important

Split Pin

Flat Washer

Exhaust

Valve

Split Pin

Connecting Pin

Push Plate

Snap-action
Unit

If the snap-action unit is being
reinstalled without being
overhauled, DO NOT loosen
the holder nuts on the push
plate (see step 7)

5. Removing/Reinstalling the Exhaust Valve Seat

Part

Disassembly

Reassembly

Exhaust Valve
Seat

• Using a 27 mm (1

in) socket wrench, remove the

exhaust valve seat from the cover unit

• Tighten to a torque of

160 N

⋅

m (115 lbf

⋅

ft).

Exhaust Valve
Seat Gasket

• Remove gasket and clean sealing surfaces on the

exhaust valve seat and the cover unit

• Replace with a new

gasket

(1 N

⋅

≈

10 kg

⋅

cm)

Cover Unit

Exhaust Valve Seat
Gasket

Exhaust Valve Seat

Содержание PowerTrap GP10F



































Результаты поиска

Содержание PowerTrap GP10F

Отзывы:

Похожие инструкции для PowerTrap GP10F

Бренды по названию

Популярные бренды

TLV PowerTrap GP10F, Инструкция по эксплуатации

Результаты поиска

Содержание PowerTrap GP10F

Отзывы:

Похожие инструкции для PowerTrap GP10F

Бренды по названию

Популярные бренды