TLV PowerTrap GP10F Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 35

background image

172-65378MA-03 (GP10F PowerTrap) 23 Apr 2019

27

7. Checking/Adjusting the Gap between the Push Plate and the Motive

Medium Intake Valve

It is necessary to inspect the gap to determine whether adjustment is necessary

only

when installing a new snap-action unit or an overhauled snap-action unit (from this or
another PowerTrap). A feeler (go/no-go) gauge is supplied with each GP10F and
replacement snap-action unit.

Step

Procedure

Check the Gap
Between the
Push Plate and
the Motive
Medium Intake
Valve

• The snap-action unit must be connected to the cover

unit before the gap inspection can be carried out. The
float should be placed in its lowest position (the
motive medium intake valve should be closed and the
exhaust valve should be open)

• To check the gap, carefully slide the thin end of the

feeler gauge (marked I.V.) into the gap between the
push plate and motive medium intake valve

• If the gap is already adjusted properly

(2±0.3 mm, 0.079±0.012 in), the gauge
will stop when the valve contacts the
no-go lip.

• The valve is free to move vertically, so

be certain to hold the base of the
gauge flush with the push plate, and do
not force the gauge past the no-go lip.

“Go” “No-go”

Section

Section

Adjusting the
gap between
the push plate
and the motive
medium intake
valve

• When a snap-action unit that has been removed from the cover is reinstalled

without being overhauled, do not loosen the holder nuts from the push plate.

• If the previous inspection reveals that the gap is out of the accepted range

(2±0.3 mm, 0.079±0.012 in), proceed with gap adjustment.

• Loosen the push plate holder nuts with two 22 mm (

⅞ in) wrenches, one an

open-end wrench, the other an open-end torque wrench.

• Set the position with the upper nut, then finger-tighten the lower nut.
• Recheck the gap with the feeler gauge.
• When the clearance is correct, hold the upper nut steady with the open-end

wrench and tighten the lower nut with the open-end torque wrench to a torque of
60 N

⋅

m (44 lbf

⋅

ft).

• Recheck the gap and, if necessary, repeat the adjustment procedure.

(1 N

⋅

m

≈

10 kg

⋅

cm)

Feeler Gauge

Use this end

Push Plate

Motive Medium

Intake Valve

Feeler Gauge

Motive Medium

Intake Valve

Push Plate

Open-end Wrench

Open-end Torque

Wrench

«
...
26
27
28
29
30
...
»

Содержание PowerTrap GP10F




































Отзывы:

Нет отзывов

Похожие инструкции для PowerTrap GP10F

Бренд: Danfoss Страницы: 12

Бренд: Kaisai Страницы: 40

Water Jet Lightning

Бренд: Oase Страницы: 28

AquaMax Eco Premium 4000

Бренд: Oase Страницы: 120

Бренд: Oase Страницы: 9

Бренд: veito Страницы: 40

Бренд: Davey Страницы: 4

Бренд: DROPSA Страницы: 9

TriScroll 620 Series

Бренд: Agilent Technologies Страницы: 26

Бренд: Homa Страницы: 72

Point-of-Use Drinking Water System

Бренд: R-Can Страницы: 12

Бренд: Wacker Neuson Страницы: 123

Aquantia KHPMS-BI Series

Бренд: Kaysun Страницы: 40

Бренд: WACKER Group Страницы: 66

Бренд: Lamborghini Caloreclima Страницы: 62

Бренд: FLOJET Страницы: 4

Krystal Clear SF10220

Бренд: Intex Страницы: 27

Бренд: BUSCH Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды