TLV GP10 Скачать руководство пользователя страница 8

Страница: 8 / 41

172-65318MA-04 (GP10/GT10/GP14/GT14 PowerTrap) 23 Nov 2018

Specifications

Install properly and DO NOT use this product outside the recommended

operating pressure, temperature and other specification ranges.

Improper use may result in such hazards as damage to the product or

malfunctions which may lead to serious accidents. Local regulations

may restrict the use of this product to below the conditions quoted.

CAUTION

Use only under conditions in which no freeze-up will occur. Freezing

may damage the product, leading to fluid discharge, which may cause

burns or other injury.

CAUTION

Refer to the product nameplate for detailed specifications.

* Maximum allowable pressure (PMA) and maximum allowable temperature (TMA) are

PRESSURE SHELL DESIGN CONDITIONS,

NOT

OPERATING CONDITIONS.

** Valve No. is displayed for products with options. This item is omitted from the nameplate when

there are no options.

Motive Medium
Pressure Range

GP10/GT10

0.03 – 1.05 MPaG 0.3 – 10.5 barg

5 – 150 psig

GP14/GT14

0.03 – 1.4 MPaG

0.3– 14 barg

5 – 200 psig

GP14/GT14 (Cast Iron in Europe)

0.03 – 1.3 MPaG

0.3 – 13 barg

5 – 185 psig

Maximum Allowable
Back Pressure

0.05 MPa / 0.5 bar / 7 psi less than motive medium pressure used

(but not to exceed 1.05 MPaG/10.5 barg/150 psig for the GP14/GT14)

Configuration

Model

Maximum Allowable Pressure*

Nominal Diameter

Maximum Operating Temperature
(TMO)

Maximum Operating Pressure

Valve No.**

Serial Number

Maximum Allowable Temperature
(TMA)*

Snap-action Unit

Pumped Medium
Inlet

Pumped Medium

Outlet

Lever Unit

Motive Medium Inlet

Rc(PT) 1
Exhaust Outlet

Cover

Cover Gasket

Float

Body

Steam Trap

Cover Bolt

Nameplate

Pumped
Medium
Inlet

Pumped

Medium
Outlet

Motive
Medium Inlet

Exhaust Outlet

Plug

Intake
Valve Unit

Exhaust Valve Unit

Rc(PT) 3
Pumped Medium
Inlet

Rc(PT) 2
Pumped Medium
Outlet

GP10/GP14

Rc(PT) 1
Exhaust Outlet

GT10/GT14

Содержание GP10









































Результаты поиска

Содержание GP10

Отзывы:

Похожие инструкции для GP10

Бренды по названию

Популярные бренды

TLV GP10, Инструкция по эксплуатации

Результаты поиска

Содержание GP10

Отзывы:

Похожие инструкции для GP10

Бренды по названию

Популярные бренды