TLV GP10 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 41

background image

172-65318MA-04 (GP10/GT10/GP14/GT14 PowerTrap) 23 Nov 2018

19

Operation and Periodic Inspection

•

After all piping work has been completed in accordance with the

specific piping system designed when the decision to utilize the

PowerTrap was made, check once again to make sure that all pipe

connections have been tightened, gaskets have been inserted where

needed and all parts are securely installed.

•

When beginning operation, make sure that the operator stays well clear

of the release area of the vent line and overflow piping.

At the start-up of operation, large quantities of condensate may flow,

causing the PowerTrap to momentarily overload. If this occurs in open

systems, hot condensate may spurt from the vent piping or overflow

piping and could result in burns, other injuries or damage to equipment.

WARNING

Install properly and DO NOT use this product outside the recommended

operating pressure, temperature and other specification ranges.

Improper use may result in such hazards as damage to the product or

malfunctions which may lead to serious accidents. Local regulations

may restrict the use of this product to below the conditions quoted.

CAUTION

When disassembling or removing the product, wait until the internal

pressure equals atmospheric pressure and the surface of the product

has cooled to room temperature. Disassembling or removing the

product when it is hot or under pressure may lead to discharge of fluids,

causing burns, other injuries or damage.

CAUTION

Be sure to use only the recommended components when repairing the

product, and NEVER attempt to modify the product in any way. Failure to

observe these precautions may result in damage to the product or burns

or other injury due to malfunction or the discharge of fluids.

CAUTION

Installation, inspection, maintenance, repairs, disassembly, adjustment and valve
opening/closing should be carried out only by trained maintenance personnel.

Operation

(1) Valve Operation

Refer to the drawings in “Installation” on pages 8 and 9 to become familiar with the
symbols used for the various valves.
If water hammer has occurred, immediately cease operation and close any valves
that are operating.

a) Slowly open the valve [Ve] on the exhaust pipe.

b) Slowly open the valve [Vm] on the motive medium supply pipe.

Make sure that there is no sound of flow from the exhaust pipe [Se] or the
pumped medium inlet pipe [Si].

c) Slowly open the valve [Vo] on the pumped medium outlet pipe.

d) Slowly open the valve [Vi] on the pumped medium inlet pipe.

When using a valve for air/gas discharge [Va] for venting air on a closed system,
leave the valve [Va] slightly open until the PowerTrap has cycled 2 or 3 times in
order to release any air inside the system, then close the valve [Va].

«
...
18
19
20
21
22
...
»

Содержание GP10










































Отзывы:

Нет отзывов

Похожие инструкции для GP10

Бренд: Dux Страницы: 20

Бренд: QED Страницы: 33

Бренд: D-D The Aquarium Solution Страницы: 8

Бренд: MULTIQUIP Страницы: 35

Бренд: Navien Страницы: 2

Бренд: AES Страницы: 38

Бренд: Barmesa Pumps Страницы: 13

Бренд: Lochinvar Страницы: 1

Бренд: DAB Страницы: 708

Бренд: FLORABEST Страницы: 48

Бренд: WACKER Group Страницы: 60

Бренд: Calpeda Страницы: 48

Бренд: PMP Страницы: 8

Бренд: Oase Страницы: 179

Бренд: Rinnai Страницы: 20

Hydroheat A650YRRTL5

Бренд: Apollo Страницы: 24

Бренд: Oceanic Страницы: 8

Бренд: F.F. Group Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды