TLV GP10 Скачать руководство пользователя страница 40

Страница: 40 / 41

172-65318MA-04 (GP10/GT10/GP14/GT14 PowerTrap) 23 Nov 2018

Product Warranty

1. Warranty Period

One year following product delivery.

2. Warranty Coverage

TLV CO., LTD. warrants this product to the original purchaser to be free from

defective materials and workmanship. Under this warranty, the product will be

repaired or replaced at our option, without charge for parts or labor.

3. This product warranty will not apply to cosmetic defects, nor to any product whose

exterior has been damaged or defaced; nor does it apply in the following cases:

Malfunctions due to improper installation, use, handling, etc., by other

than TLV CO., LTD. authorized service representatives.

Malfunctions due to dirt, scale, rust, etc.

Malfunctions due to improper disassembly and reassembly, or

inadequate inspection and maintenance by other than TLV CO., LTD.

authorized service representatives.

Malfunctions due to disasters or forces of nature.

Accidents or malfunctions due to any other cause (such as water

hammer) beyond the control of TLV CO., LTD.

4. Under no circumstances will TLV CO., LTD. be liable for consequential economic loss

damage or consequential damage to property.

Содержание GP10









































Результаты поиска

Содержание GP10

Отзывы:

Похожие инструкции для GP10

Бренды по названию

Популярные бренды

TLV GP10, Инструкция по эксплуатации

Результаты поиска

Содержание GP10

Отзывы:

Похожие инструкции для GP10

Бренды по названию

Популярные бренды